SSD0858Z Ver la hoja de datos (PDF) - Solomon Systech
Número de pieza
componentes Descripción
Fabricante
SSD0858Z Datasheet PDF : 45 Pages
| |||
Bit Pattern
1000 1000
WB3WB2WB1WB0 WA3WA2WA1WA0
1000 1001
WD3WD2WD1WD0 WC3WC2WC1WC0
1000 1010
LB3LB2LB1LB0 LA3LA2LA1LA0
1000 1011
LD3LD2LD1LD0 LC3LC2LC1LC0
1000 1100
DB3DB2DB1DB0 DA3DA2DA1DA0
1000 1101
DD3DD2DD1DD0 DC3DC2DC1DC0
1000 1110
BB3BB2BB1BB0 BA3BA2BA1BA0
1000 1111
BD3BD2BD1BD0 BC3BC2BC1BC0
Command
Set White Mode,
Frame 2nd & 1st
Set White Mode,
Frame 4th & 3rd
Set Light Gray Mode,
Frame 2nd & 1st
Set Light Gray Mode,
Frame 4th & 3rd
Set Dark Gray Mode,
Frame 2nd & 1st
Set Dark Gray Mode,
Frame 4th & 3rd
Set Black Mode,
Frame 2nd & 1st
Set Black Mode,
Frame 4th & 3rd
Description
Set gray scale mode and register. These are two-byte
commands used to specify the contrast levels for the
gray scale, 4 levels available.
After power on reset:
WA0~3 = WB0~3 = WC0~3 = WD0~3 = 0000
LA0~3 = 1001
LB0~3 = LC0~3 = LD0~3 = 0000
DA0~3 = DB0~3 = DC0~3 = 1001
DD0~3 = 0000
BA0~3 = BB0~3 = BC0~3 = BD0~3 = 1001
Memory Content
1st Byte 2nd Byte
Gray Mode
0
0
White
0
1
Light Gray
1
0
Dark Gray
1
1
Black
1001 0 FRC PWM1 PWM0
1010 000S0
1010 001C0
1010 010E0
1010 011R0
1010 1001
1010 1011
1010 111D0
Set PWM and FRC
Set Segment Re-map
Set Icon Enable
Set Entire Display On/Off
Set Normal/Inverse
Display
Set Power Save Mode
Start Internal Oscillator
Set Display On/Off
Set PWM and FRC for gray-scale operation.
FRC = 0 : 4-frame (POR)
FRC = 1 : 3-frame
PWM = 00 & 01 : 9-levels (POR)
PWM = 10 : 12-levels
PWM = 11 : 15-levels
MODE=L
S0=0: column address 00H is mapped to SEG0 (POR)
S0=1: column address 67H is mapped to SEG0
MODE=H
S0=0: column address 00H is mapped to SEG0 (POR)
S0=1: column address 5FH is mapped to SEG0
C0=0: Disable icon row (Mux = 16 to 64, POR)
C0=1: Enable icon row (Mux = 17 to 65)
E0=0: Normal display (display according to RAM
contents, POR)
E0=1: All pixels are ON regardless of the RAM contents
*Note: This command will override the effect of “Set
Normal/Invert Display”
R0=0: Normal display (display according to RAM
contents, POR)
R0=1: Invert display (ON and OFF pixels are inverted)
*Note: This command will not affect the display of the
icon lines
Sleep Mode:
Oscillator: OFF
LCD Power Supply: OFF
COM/SEG Outputs: VSS
This command starts the internal oscillator. Note that
the oscillator is OFF after reset, so this instruction must
be executed for initialization
Turn the display on and off without modifying the
content of the RAM. (0: off, 1: on)
This command has priority over Entire Display On/Off
and Inverse Display On/Off. Commands are accepted
while the display is off, but the visual state of the
display does not change.
SSD0858
Rev 1.0
11/2002
20
SOLOMON
Share Link: 