CAT93C76(2004) Ver la hoja de datos (PDF) - Catalyst Semiconductor => Onsemi
Número de pieza
componentes Descripción
Fabricante
CAT93C76 Datasheet PDF : 10 Pages
| |||
CAT93C76
ABSOLUTE MAXIMUM RATINGS*
Temperature Under Bias .................. -55°C to +125°C
Storage Temperature ........................ -65°C to +150°C
Voltage on any Pin with
Respect to Ground(1) ............. -2.0V to +VCC +2.0V
VCC with Respect to Ground ................ -2.0V to +7.0V
Lead Soldering Temperature (10 secs) ............ 300°C
Output Short Circuit Current(2) ........................ 100 mA
*COMMENT
Stresses exceeding those listed under “Absolute Maxi-
mum Ratings” may cause permanent damage to the
device. These are stress ratings only, and functional
operation of the device at these or any other conditions
outside of those listed in the operational sections of this
specification is not implied. Exposure to any absolute
maximum rating for extended periods may affect device
performance and reliability.
RELIABILITY CHARACTERISTICS
Symbol
Parameter
Reference Test Method
Min
Typ
NEND(3)
Endurance
MIL-STD-883, Test Method 1033 1,000,000
TDR(3)
Data Retention
MIL-STD-883, Test Method 1008
100
VZAP(3)
ESD Susceptibility MIL-STD-883, Test Method 3015
2000
ILTH(3)(4)
Latch-Up
JEDEC Standard 17
100
Max
Units
Cycles/Byte
Years
Volts
mA
D.C. OPERATING CHARACTERISTICS
VCC = +1.8V to +5.5V, unless otherwise specified.
Symbol
Parameter
Test Conditions
Min
ICC1
Power Supply Current
(Write)
fSK = 1MHz
VCC = 5.0V
ICC2
Power Supply Current
(Read)
fSK = 1MHz
VCC = 5.0V
ISB1
Power Supply Current
(Standby) (x8 Mode)
CS = 0V
ORG=GND
ISB2
Power Supply Current
(Standby) (x16Mode)
CS=0V
ORG=Float or VCC
ILI
Input Leakage Current
VIN = 0V to VCC
ILO
Output Leakage Current VOUT = 0V to VCC, CS = 0V
ILORG
ORG Pin Leakage Current ORG = GND or ORG = VCC
VIL1
Input Low Voltage
VIH1
Input High Voltage
4.5V ≤ VCC ≤ 5.5V
-0.1
4.5V ≤ VCC ≤ 5.5V
2
VIL2
Input Low Voltage
1.8V ≤ VCC < 4.5V
0
VIH2
Input High Voltage
1.8V ≤ VCC < 4.5V
VCC x 0.7
VOL1
Output Low Voltage
4.5V ≤ VCC ≤ 5.5V
IOL = 2.1mA
VOH1
Output High Voltage
4.5V ≤ VCC ≤ 5.5V
2.4
IOH = -400µA
VOL2
Output Low Voltage
1.8V ≤ VCC < 4.5V
IOL = 100µA
VOH2
Output High Voltage
1.8V ≤ VCC < 4.5V
IOH = -100µA
VCC - 0.2
Typ
Max
Units
1
3
mA
300
500
µA
2
10
µA
0(5)
10
µA
0(5)
10
µA
0(5)
10
µA
1
10
µA
0.8
V
VCC + 1
V
VCC x 0.2
V
VCC+1
V
0.4
V
V
0.1
V
V
Note:
(1) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Maximum DC
voltage on output pins is VCC +0.5V, which may overshoot to VCC +2.0V for periods of less than 20 ns.
(2) Output shorted for no more than one second.
(3) These parameters are tested initially and after a design or process change that affects the parameter.
(4) Latch-up protection is provided for stresses up to 100 mA on I/O pins from –1V to VCC +1V.
(5) 0 µA is defined as less than 900 nA.
Doc. No. 1090, Rev. A
2
Share Link: 