ISL9011AIRFDZ Ver la hoja de datos (PDF) - Renesas Electronics
Número de pieza
componentes Descripción
Fabricante
ISL9011AIRFDZ Datasheet PDF : 12 Pages
| |||
ISL9011A
Absolute Maximum Ratings
Supply Voltage (VIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7.1V
VO1, VO2 Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +3.6V
All Other Pins . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to (VIN + 0.3)V
Recommended Operating Conditions
Ambient Temperature Range (TA) . . . . . . . . . . . . . . .-40°C to +85°C
Supply Voltage (VIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3V to 6.5V
Thermal Information
Thermal Resistance (Notes 4, 5)
JA (°C/W) JC (°C/W)
10 Ld 3x3 DFN Package . . . . . . . . . . .
50
10
Junction Temperature Range . . . . . . . . . . . . . . . . .-40°C to +125°C
Operating Temperature Range . . . . . . . . . . . . . . . . .-40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
4. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
Tech Brief TB379.
5. For JC, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications
PARAMETER
Unless otherwise noted, all parameters are guaranteed over the operational supply voltage and temperature
range of the device as follows: TA = -40°C to +85°C; VIN = (VO + 1.0V) to 6.5V with a minimum VIN of 2.3V;
CIN = 1µF; CO = 1µF; CBYP = 0.01µF
SYMBOL
TEST CONDITIONS
MIN
MAX
(Note 7) TYP (Note 7) UNITS
DC CHARACTERISTICS
Supply Voltage
Ground Current
Shutdown Current
UVLO Threshold
Regulation Voltage Accuracy
Line Regulation
Load Regulation
Maximum Output Current
VIN
2.3
6.5
V
Quiescent condition: IO1 = 0µA; IO2 = 0µA
IDD1 One LDO active
25
40
µA
IDD2 Both LDO active
45
60
µA
IDDS @ +25°C
0.1 1.0
µA
VUV+
1.9 2.1 2.3
V
VUV-
1.6 1.8 2.0
V
Variation from nominal voltage output, VIN = VO + 0.5 to 5.5V, -1.8
TJ = -40°C to +125°C
+1.8
%
VIN = (VOUT + 1.0V relative to highest output voltage) to 5.5V -0.2
0
0.2
%/V
IOUT = 100µA to 150mA (VO1 and VO2)
0.1 0.7
%
IOUT = 100µA to 300mA (VO2)
1.0
%
IMAX VO1: Continuous
150
mA
VO2: Continuous
300
mA
Internal Current Limit
Dropout Voltage (Note 6)
Thermal Shutdown Temperature
AC CHARACTERISTICS
ILIM
VDO1
VDO2
VDO3
VDO4
TSD+
TSD-
IO = 150mA; VO 2.1V (VO1)
IO = 300mA; VO < 2.5V (VO2)
IO = 300mA; 2.5V VO 2.8V (VO2)
IO = 300mA; VO > 2.8V (VO2)
350 475 600
mA
125 200
mV
300 500
mV
250 400
mV
200 325
mV
145
°C
110
°C
Ripple Rejection
IO = 10mA, VIN = 2.8V(min), VO = 1.8V, CBYP = 0.1µF
@ 1kHz
70
dB
@ 10kHz
55
dB
@ 100kHz
40
dB
Output Noise Voltage
IO = 100A, VO = 1.5V, TA = +25°C, CBYP = 0.1µF
BW = 10Hz to 100kHz
30
µVRMS
FN6437 Rev 2.00
September 1, 2015
Page 3 of 12
Share Link: 