ISL8200MM Ver la hoja de datos (PDF) - Renesas Electronics
Número de pieza
componentes Descripción
Fabricante
ISL8200MM Datasheet PDF : 24 Pages
| |||
ISL8200MM
Absolute Maximum Ratings
Input Voltage, PVIN, VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +27V
Driver Bias Voltage, PVCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6.5V
Signal Bias Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6.5V
BOOT/UGATE Voltage, VBOOT . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +36V
Phase Voltage, VPHASE . . . . . . . . . . . . . . . . . . . VBOOT - 7V to VBOOT + 0.3V
BOOT to PHASE Voltage,
VBOOT - VPHASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VCC + 0.3V
Input, Output or I/O Voltage . . . . . . . . . . . . . . . . . . . . . . -0.3V to VCC + 0.3V
ESD Rating
Human Body Model (Tested per JESD22-A114E) . . . . . . . . . . . . . . . . 2kV
Machine Model (Tested per JESD22-A115-A) . . . . . . . . . . . . . . . . . 200V
Charge Device Model (Tested per JESD22-C101C). . . . . . . . . . . . . . . 1kV
Latch Up (Tested per JESD-78B; Class 2, Level A) . . . . . . . . . . . . . . 100mA
Thermal Information
Thermal Resistance (Typical)
JA (°C/W) JC (°C/W)
QFN Package (Notes 3, 4) . . . . . . . . . . . . . .
13
2.0
Maximum Storage Temperature Range . . . . . . . . . . . . . -55°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Recommended Operating Conditions
Input Voltage, VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5V to 20V
Input Voltage, PVIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3V to 20V
Driver Bias Voltage, PVCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5V to 5.6V
Signal Bias Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5V to 5.6V
Boot to Phase Voltage (Overcharged),
VBOOT - VPHASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <6V
Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . -55°C to +125°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
3. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. (i.e., 4-layer
type without thermal vias – see tech brief TB379) per JEDEC standards except that the top and bottom layers assume solid planes.
4. For JC, case temperature location is the center of the package underside.
Electrical Specifications
PARAMETER
SYMBOL
TEST CONDITIONS
VCC SUPPLY CURRENT
Nominal Supply VIN Current
IQ_VIN
Nominal Supply VIN Current
IQ_VIN
Shutdown Supply VCC Current
IVCC
INTERNAL LINEAR REGULATOR (Note 6)
PVIN = VIN = 20V; No Load; FSW = 700kHz
PVIN = VIN = 4.5V; No Load; FSW = 700kHz
EN = 0V, VCC = 2.97V
Maximum Current
IPVCC
PVCC = 4V TO 5.6V
PVCC = 3V TO 4V
Saturated Equivalent Impedance
POWER-ON RESET (Note 6)
RLDO P-Channel MOSFET (VIN = 5V)
Rising VCC Threshold
Falling VCC Threshold
Rising PVCC Threshold
Falling PVCC Threshold
System Soft-start Delay
tSS_DLY After PLL, VCC, and PVCC PORs, and EN above
their thresholds
ENABLE (Note 6)
Turn-On Threshold Voltage
Hysteresis Sink Current
Undervoltage Lockout Hysteresis
Sink Current
Sink Impedance
IEN_HYS
VEN_HYS
IEN_SINK
REN_SINK
VEN_RTH = 10.6V; VEN_FTH = 9V
RUP = 53.6kΩ, RDOWN = 5.23kΩ
VEN = 1V
VEN = 1V
TYP
MIN
(Note 5)
MAX UNITS
36
mA
27
mA
9
mA
320
mA
150
mA
1
Ω
2.85
2.65
2.85
2.65
384
(Note 8)
(Note 8)
(Note 8)
(Note 8)
V
V
V
V
Cycles
(Note 8)
0.8
(Note 8) V
(Note 8)
30
(Note 8) μA
1.6
V
(Note 8)
mA
(Note 8) Ω
FN7690 Rev 2.00
Mar 15, 2013
Page 7 of 24
Share Link: 