ISL80136(2011) Ver la hoja de datos (PDF) - Intersil
Número de pieza
componentes Descripción
Fabricante
ISL80136 Datasheet PDF : 9 Pages
| |||
ISL80136
Absolute Maximum Ratings
IN pin to GND Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to +45V
OUT pin to GND Voltage . . . . . . . . . . . . . . . . . . . . . . . . .. . .GND - 0.3V to 16V
EN pin to GND Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .GND - 0.3V to IN
ADJ pin to GND Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to3V
Output Short-circuit Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indefinite
ESD Rating
Human Body Model (Tested per JESD22-A114E) . . . . . . . . . . . . . . . . 5kV
Machine Model (Tested per JESD-A115-A) . . . . . . . . . . . . . . . . . . . 200V
Charge Device Model (Tested per JESD22-C101C). . . . . . . . . . . . . 2.2kV
Latch Up (Tested per JESD78B; Class II, Level A) . . . . . . . . . . . . . . . 100mA
Thermal Information
Thermal Resistance (Typical)
θJA (°C/W) θJC (°C/W)
8 Ld EPSOIC Package (Notes 4, 5). . . . . . . .
50
9
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . . . . . .-65°C to +175°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Recommended Operating Conditions
Ambient Temperature Range . . . . . . . . . . . . . . . . . . . . . . -40°C to +125°C
IN pin to GND Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+6V to +40V
OUT pin to GND Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+2.5V to +12V
EN pin to GND Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0V to +40V
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379.
5. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications Recommended Operating Conditions, unless otherwise noted. VIN = 14V, IOUT = 1mA, CIN = 0.1μF,
COUT = 10μF, TA = TJ = -40°C to +125°C, unless otherwise noted. Typical specifications are at TA = +25°C. Boldface limits apply over the operating
temperature range, -40°C to +125°C.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
MAX
(Note 8) TYP (Note 8) UNIT
Input Voltage Range
Guaranteed Output Current
ADJ Reference Voltage
Line Regulation
Load Regulation
Dropout Voltage (Note 6)
Shutdown Current
Quiescent Current
Power Supply Rejection Ratio
EN FUNCTION
VIN
IOUT
VIN = VOUT + VDO
VREF
EN = High, VIN = 14V, IOUT = 0.1mA
ΔVOUT/ΔVIN 3V ≤ VIN ≤ 40V, IOUT = 1mA
ΔVOUT/ΔIOUT VIN = VOUT +VD, IOUT = 100µA to 50mA
ΔVDO
IOUT = 1mA, VOUT = 3.3V
IOUT = 50mA, VOUT = 3.3V
IOUT = 1mA, VOUT = 5V
IOUT = 50mA, VOUT = 5V
ISHDN
EN = LOW
IQ
EN = HIGH, IOUT = 0mA
EN = HIGH, IOUT = 1mA
EN = HIGH, IOUT = 10mA
EN = HIGH, IOUT = 50mA
PSRR f = 100Hz; Vin_ripple = 500mVP-P; Load = 50mA
6
40
V
50
mA
1.211 1.223 1.235 V
0.04 0.115 %
0.25 0.5 %
10
38 mV
130 340 mV
10
48 mV
120 350 mV
1.8 3.64 µA
18
24 µA
22
42 µA
34
60 µA
56
82 µA
58
dB
EN Threshold Voltage
EN Pin Current
EN to Regulation Time (Note 7)
PROTECTION FEATURES
VEN_H
VEN_L
IEN
tEN
VOUT = Off to On
VOUT = On to Off
VOUT = 0V
1.485 V
0.935
V
0.026
µA
1.65 1.93 ms
Output Current Limit
ILIMIT
VOUT = 0V
60 118
mA
3
FN7970.0
December 15, 2011
Share Link: 