CMPWR280TN Ver la hoja de datos (PDF) - ON Semiconductor

Número de pieza

componentes Descripción

Fabricante

CMPWR280TN

Dual Input SmartOR Power Switch

ON Semiconductor 

CMPWR280

SPECIFICATIONS (Cont’d)

Table 3. ABSOLUTE MAXIMUM RATINGS

ESD Protection (HBM)

Parameter

Rating

2000

Units

V

Pin Voltages

VCC, VSBY ,VOUT

DRIVE

Storage Temperature Range

Operating Temperature Range

Ambient

Junction

V

[GND − 0.5] to [+6.0]

[GND − 0.5] to [VCC (VSBY) + 0.5]

−40 to +150

C

C

0 to +70

0 to +125

Power Dissipation

TO−263 (Note 1)

W

Internally Limited

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the

Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect

device reliability.

1. The maximum power dissipation of this device is internally limited by thermal shutdown circuitry. To achieve a power dissipation of 3.0 watts,

a case−to−ambient thermal resistance of 25C/W must be provided. This will typically require dedicated heatsinking ability of the printed

circuit board. For more details, please see the Typical Thermal Characteristics section.

Table 4. ELECTRICAL OPERATING CHARACTERISTICS (Note 2)

Symbol

Parameter

Conditions

Min Typ Max Units

VOUT

Regulator Output Voltage

0 mA < ILOAD < 1500 mA (VCC)

0 mA < ILOAD < 375 mA (VSBY)

3.135 3.300 3.465 V

VCCSEL

VCCDES

VCCHYST

IOUT

Select Voltage

VCC Deselect Voltage

Hysteresis Voltage

Regulator Output Current

VCC Regulator Enabled

VCC Regulator Disabled

VCC Hysteresis (Note 3)

VCC Selected

VSBY Selected

4.50 4.70 V

3.90 4.10

V

0.40

V

1500 2500

mA

375 750

ISC

Short−circuit Output Current

VCC Selected

VSBY Selected

800

mA

200

IRCC

VCC Pin Reverse Leakage

VSBY = 5.0 V, VCC = 0 V

10 100 mA

IRSBY

VSBY Pin Reverse Leakage

VSBY = 0 V, VCC = 5.0 V

10 100 mA

VR LOAD VCC Load Regulation

VCC Selected, ILOAD = 15 mA to 1500 mA

30

mV

VSBY Load Regulation

VSBY Selected, ILOAD = 5 mA to 375 mA

30

VR LINE Line Regulation

VCC = 4.5 to 5.5 V, ILOAD = 5 mA

5

mV

ICC

VCC Supply Current

VCC Selected, IOUT = 0 mA

VCCDES > VCC > VAUX or VOUT

1.5 3.0 mA

0.1 0.2

ISBY

VSBY Supply Current

VSBY Selected, IOUT = 0 mA

1.5 3.0 mA

IGND

Ground Pin Current (Note 4)

Regulator Disabled (only VOUT Present)

Regulator Selected, ILOAD = 5 mA

Regulator Selected = 5 V, ILOAD = 500 mA

0.2 0.3 mA

1.5 3.0

1.8 3.5

ROH

Drive RDS High

RDS to VCC, VCC > VCCSEL

5

10 kW

ROL

Drive RDS Low

RDS to GND, VCCDES > VCC

0.5 1.0 kW

tDH

Drive High Delay

CDRIVE = 1 nF, VCC tRISE < 100 ns

5.0

ms

tDL

Drive Low Delay

CDRIVE = 1 nF, VCC tFALL < 100 ns

0.5

ms

TDISABLE Shutdown Temperature

165

C

THYST Thermal Hysteresis

30

C

2. Operating Characteristics are over Standard Operating Conditions unless otherwise specified.

3. The hysteresis defines the maximum level of acceptable disturbance on VCC during switching. It is recommended that the VCC source

impedance be kept below 0.15 W to ensure the switching disturbance remains below the hysteresis during select/deselect transitions.

4. Ground pin current consists of controller current (0.2 mA) and regulator current when selected.

http://onsemi.com

4

Share Link: