RP40-120512TG Ver la hoja de datos (PDF) - RECOM Electronic GmbH

Número de pieza

componentes Descripción

Fabricante

RP40-120512TG

40 Watt Single, Dual & Triple Output

RECOM Electronic GmbH 

RP40-G

DC/DC Converter

Specifications measured at Ta = 25°C, nominal input voltage, full load otherwise noted

Series

REGULATIONS

Parameter

Output Voltage Accuracy

Voltage Adjustability (7)

Line Voltage Regulation

Load Voltage Regulation

Cross Regulation

Transient Response recovery time

Condition

Single & Dual

Triple Main

Triple Auxiliary

Single & Dual

low line, high line at full load Triple Main

Triple Auxiliary

Single

Single/Dual min. load to full load Dual

Triple: main output (3.3, 5 Vout) 10% to 100% Triple Main

with 10% to 100% balanced on auxiliaries.

Auxiliary outputs 10% to 100% balanced on Auxiliary

all outputs

asymmetrical 25%/100% FL Dual

Triple: main otput (3.3, 5Vout) 100%load,

auxiliary 100%, other auxiliary 25% to 100% Triple 3.3Vout, 5Vout

load or main output (3.3, 5Vout) 25%, auxiliary Triple 12Vout, 15Vout

25%, other auxiliary 25% to 100%

25% load step change

Value

±1.0% max.

±1.0% max.

±5.0% max.

±10% max.

±0.5% max.

±1.0% max.

±5.0% max.

±0.5% max.

±1.0% max.

±2.0% max.

±5.0% max.

±5.0% max.

±1.0% max.

±5.0% max.

250μs typ.

Notes:

Note7: For the single output: Maximum output deviation is 10% inclusive of remote sense and trim. If remote sense is

not being use, the +Sense should be connected to its corresponding +Vout and likewise the -Sense should be

conneted to its corresponding -Vout.

External Output Trimming

Output Voltage Trimming

Some single/dual output Powerline converters offer the feature of trimming the output voltage over a certain range around the nominal value by using

external trim resistors. No general equation can be given for calculating the trim resistors, but the following trimtables give typical values for chosing

these trimming resistors. If voltages between the given trim points are required, extrapolate between the two nearest given values to work out the

resis tor required or use a variable resistor to set the output voltage. Output can be externally trimmed by using the method shown below.

Trim up

5(8)

RU

9(9)

Trim down

9(9)

RD

6(5)

RP40-xx3.3S

Trim up

1

Vout =

3.333

RU =

57.93

Trim down

Vout =

RD =

1

3.267

69.47

PD-4

2

3.366

26.16

2

3.234

31.23

3

3.399

15.58

3

3.201

18.49

4

3.432

10.28

5

3.465

7.11

6

3.498

4.99

7

3.531

3.48

4

3.168

12.12

5

3.135

8.29

6

3.102

5.74

7

3.069

3.92

continued on next page

REV.: 1/2016

8

3.564

2.34

8

3.036

2.56

9

3.597

1.46

9

3.003

1.50

10 %

3.63 Volts

0.75 KOhms

10 %

2.97 Volts

0.65 KOhms

www.recom-power.com

Share Link: