EDR-150-24 Ver la hoja de datos (PDF) - Unspecified

Número de pieza

componentes Descripción

Fabricante

EDR-150-24

150W Single Output Industrial DIN RAIL

Unspecified 

Authorized Distributor: Total Power International, Inc. Toll Free: 877-646-0900(US) PH# (978) 453-7272 www.total-power.com

150W Single Output Industrial DIN RAIL

EDR-150-24

SPECIFICATION

MODEL

EDR-150-24

DC VOLTAGE

24V

RATED CURRENT

6.5A / 230VAC 5.2A / 115VAC

CURRENT RANGE

0 ~ 6.5A / 230VAC 0 ~ 5.2A / 115VAC

RATED POWER

156W / 230VAC 125W / 115VAC

RIPPLE & NOISE (max.) Note.2 150mVp-p

OUTPUT

VOLTAGE ADJ. RANGE

24 ~ 28V

VOLTAGE TOLERANCE Note.3 ±1.0%

LINE REGULATION

±0.5%

LOAD REGULATION

±1.0%

SETUP, RISE TIME

1500ms, 60ms/230VAC 3000ms, 60ms/115VAC at full load

HOLD UP TIME (Typ.)

16ms/230VAC 10ms/115VAC at full load

VOLTAGE RANGE Note.6 90 ~ 264VAC 127 ~ 370VDC [DC input operation possible by connecting AC/L(+), AC/N(-)]

FREQUENCY RANGE

47 ~ 63Hz

INPUT

EFFICIENCY (Typ.)

AC CURRENT (Typ.)

INRUSH CURRENT (Typ.)

87%

2.6A/115VAC

20A/115VAC

1.7A/230VAC

35A/230VAC

LEAKAGE CURRENT

<1mA / 240VAC

OVERLOAD

PROTECTION

105 ~ 130% rated output power

Protection type : Constant current limiting, recovers automatically after fault condition is removed / 230VAC

105 ~ 150% rated output power

Protection type : Hiccup mode or constant current limiting, recovers automatically after fault condition is removed / 115VAC

OVER VOLTAGE

29 ~ 33V

Protection type : Shut down o/p voltage, re-power on to recover

OVER TEMPERATURE

WORKING TEMP.

WORKING HUMIDITY

ENVIRONMENT STORAGE TEMP., HUMIDITY

Shut down o/p voltage, re-power on to recover

-20 ~ +60℃ (Refer to "Derating Curve")

20 ~ 95% RH non-condensing

-40 ~ +85℃, 10 ~ 95% RH

SAFETY &

EMC

(Note 4)

TEMP. COEFFICIENT

VIBRATION

SAFETY STANDARDS

WITHSTAND VOLTAGE

ISOLATION RESISTANCE

EMC EMISSION

±0.03%/℃ (0 ~ 50℃)

Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6

UL508, TUV EN60950-1 approved

I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC

I/P-O/P, I/P-FG, O/P-FG:>100M Ohms / 500VDC / 25℃/ 70% RH

Compliance to EN55022 (CISPR22) Class A, EN61000-3-2, Class A (≦80% Load), EN61000-3-3

OTHERS

NOTE

EMC IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2 (EN50082-2), heavy industry level, criteria A

MTBF

472.5K hrs min. MIL-HDBK-217F (25℃)

DIMENSION

40*125.2*113.5mm (W*H*D)

PACKING

0.6Kg; 20pcs/13Kg/1.16CUFT

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets

EMC directives.

5. Installation clearances : 40mm on top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded permanently with full power.

In case the adjacent device is a heat source, 15mm clearance is recommended.

6. Derating may be needed under low input voltage. Please check the derating curve for more details.

File Name:EDR-150-24-SPEC 2014-07-07

Share Link: