HEC50 Ver la hoja de datos (PDF) - Power Mate Technology
Número de pieza
componentes Descripción
Fabricante
HEC50 Datasheet PDF : 3 Pages
| |||
Model
Number
HEC50-24S1P8
HEC50-24S2P5
HEC50-24S3P3
HEC50-24S05
HEC50-24S15
HEC50-48S1P8
HEC50-48S2P5
HEC50-48S3P3
HEC50-48S05
HEC50-48S15
Input
Range
18 – 36 VDC
18 – 36 VDC
18 – 36 VDC
18 – 36 VDC
18 – 36 VDC
36 – 75 VDC
36 – 75 VDC
36 – 75 VDC
36 – 75 VDC
36 – 75 VDC
Output
Voltage
1.8 VDC
2.5 VDC
3.3 VDC
5 VDC
15 VDC
1.8 VDC
2.5 VDC
3.3 VDC
5 VDC
15 VDC
Output Current
Min. load Full load
0mA
15 A
0mA
15 A
0mA
15 A
0mA
0mA
10 A
3.3 A
0mA
15 A
0mA
15 A
0mA
0mA
15 A
10 A
0mA
3.3 A
Line
regulation
4 mV
5 mV
7 mV
10 mV
30 mV
4 mV
5 mV
7 mV
10 mV
30 mV
Load
regulation
6 mV
8 mV
10 mV
15 mV
45 mV
6 mV
8 mV
10 mV
15 mV
45 mV
Input Current
Eff (4)
No load(3) Full load(2) (%)
120mA
1.36 A
86
100mA
1.86 A
87
120mA
2.40 A
89
120mA
2.40 A
90
190mA
2.40 A
89
80mA
0.67 A
87
80mA
0.93 A
88
110mA
1.19 A
90
90mA
1.19 A
91
130mA
1.20 A
90
Note
1. BELLCORE TR-NWT-000332. Case 1: 50% Stress, Temperature at 40ºC.
MIL-HDBK-217F Notice2 @Ta=25 ºC, Full load(Ground, Benign, controlled environment).
2. Maximum value at nominal input voltage and full load.
3. Typical value at nominal input voltage and no load.
4. Typical value at nominal input voltage and full load.
5. Maximum output deviation is 10% inclusive of remote sense. If remote sense is not being used, the + sense should be connected to its corresponding
+OUTPUT and likewise the –sense should be connected to its corresponding –OUTPUT.
6. Measured with a 1μF M/C and a 10μF T/C.
7. The negative/ positive logic and pin length are optional ( see table ). The pin voltage is referenced to –Vin.
8. Heat sink is optional and P/N: 7G-0021A-F, 7G-0022A-F, 7G-0023A-F, 7G-0024A-F.
9. The HEC50 meets EN55022 class A and class B only with external components connected with the input pins.
10. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5.
The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220μF/100V, ESR 48mΩ.
11. BASEPLATE GROUNDING：Base-plate should be grounded at one of the four screw bolts prior to operation.
12. The converter is provided by basic insulation.
Pin 1,2,3,4,6,7,8. DIA. 0.040 (1.02mm)
Pin 5,9. DIA. 0.080 (2.03mm)
All dimensions in inches (mm)
Tolerance :x.xx±0.02 (x.x±0.5)
x.xxx±0.01 (x.xx±0.25)
Pin pitch tolerance ±0.01 (0.25)
Pin dimension tolerance ±0.004(0.1)
EXTERNAL OUTPUT
Output can be externally trimmed by PIN
using the method shown below.
1
TRIM UP
TRIM DOWN
2
7
6
3
4
RU
RD
5
8
7
6
7
8
9
PIN CONNECTION
Define
Diameter
- INPUT
CASE
CTRL
+ INPUT
- OUTPUT
- SENSE
TRIM
+ SENSE
+ OUTPUT
0.04 Inches
0.04 Inches
0.04 Inches
0.04 Inches
0.08 Inches
0.04 Inches
0.04 Inches
0.04 Inches
0.08 Inches
PRODUCT OPTIONS TABLE
Option
Suffix
Negative remote ON/OFF logic, 0.20” pin length (standard) -
Negative remote ON/OFF logic, 0.145” pin length
-L
Negative remote ON/OFF logic, 0.11” pin length
-K
Positive remote ON/OFF logic, 0.20” pin length
-P
Positive remote ON/OFF logic, 0.145” pin length
-S
Positive remote ON/OFF logic, 0.11” pin length
-M
Example：HEC50-48S3P3-P
Page 2 of 3 Issued Date：2008/05/21
Share Link: 