AZ100E116FN Ver la hoja de datos (PDF) - Arizona Microtek, Inc
Número de pieza
componentes Descripción
Fabricante
AZ100E116FN Datasheet PDF : 5 Pages
| |||
AZ10E116
AZ100E116
10K PECL DC Characteristics (VEE = GND, VCC = VCCO = +5.0V)
Symbol
Characteristic
-40°C
0°C
25°C
85°C
Unit
Min Typ Max Min Typ Max Min Typ Max Min Typ Max
VOH
Output HIGH Voltage1,2 3920
VOL
Output LOW Voltage1,2
3050
VIH
Input HIGH Voltage1
3770
VIL
Input LOW Voltage1
3050
VBB
Reference Voltage1
3570
4110
3350
4110
3500
3700
3980
3050
3830
3050
3620
4160
3370
4160
3520
3730
4020
3050
3870
3050
3650
4190
3370
4190
3520
3750
4090
3050
3940
3050
3690
4280 mV
3405 mV
4280 mV
3555 mV
3810 mV
IIH
Input HIGH Current
150
150
150
150
μA
IIL
Input LOW Current
0.5
0.5
0.5
0.5
μA
IEE
Power Supply Current
29
35
29
35
29
35
29
35
mA
1. For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value.
2. Each output is terminated through a 50Ω resistor to VCC – 2V.
100K ECL DC Characteristics (VEE = -4.2V to -5.46V, VCC = VCCO = GND)
Symbol
Characteristic
-40°C
0°C
25°C
85°C
Unit
Min Typ Max Min Typ Max Min Typ Max Min Typ Max
VOH
Output HIGH Voltage1 -1085 -1005 -880 -1025 -955 -880 -1025 -955 -880 -1025 -955 -880 mV
VOL
Output LOW Voltage1 -1830 -1695 -1555 -1810 -1705 -1620 -1810 -1705 -1620 -1810 -1705 -1620 mV
VIH
Input HIGH Voltage
-1165
-880 -1165
-880 -1165
-880 -1165
-880 mV
VIL
Input LOW Voltage
-1810
-1475 -1810
-1475 -1810
-1475 -1810
-1475 mV
VBB
Reference Voltage
-1380
-1260 -1380
-1260 -1380
-1260 -1380
-1260 mV
IIH
Input HIGH Current
150
150
150
150
μA
IIL
Input LOW Current
0.5
0.5
0.5
0.5
μA
IEE
Power Supply Current
29
35
29
35
29
35
29
40
mA
1. Each output is terminated through a 50Ω resistor to VCC – 2V.
100K PECL DC Characteristics (VEE = GND, VCC = VCCO = +5.0V)
Symbol
Characteristic
-40°C
0°C
25°C
85°C
Unit
Min Typ Max Min Typ Max Min Typ Max Min Typ Max
VOH
Output HIGH Voltage1,2 3915 3995 4120 3975 4045 4120 3975 4045 4120 3975 4045 4120 mV
VOL
Output LOW Voltage1,2
3170 3305 3445 3190 3295 3380 3190 3295 3380 3190 3295 3380
mV
VIH
Input HIGH Voltage1
3835
4120 3835
4120 3835
4120 3835
4120 mV
VIL
Input LOW Voltage1
3190
3525 3190
3525 3190
3525 3190
3525 mV
VBB
Reference Voltage1
3620
3740 3620
3740 3620
3740 3620
3740 mV
IIH
Input HIGH Current
150
150
150
150
μA
IIL
Input LOW Current
0.5
0.5
0.5
0.5
μA
IEE
Power Supply Current
29
35
29
35
29
35
29
40
mA
1. For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value.
2. Each output is terminated through a 50Ω resistor to VCC – 2V.
AC Characteristics (VEE =10E(-4.94V to -5.46V), 100E(-4.2V to -5.46V); VCC =VCCO =GND or VEE=GND,
VCC=VCCO =10E(+4.94V to +5.46V),100E(+4.2V to +5.46V) )
Symbol
Characteristic
-40°C
0°C
25°C
85°C
Unit Condition
Min Typ Max Min Typ Max Min Typ Max Min Typ Max
Propagation Delay to
tPLH /tPHL
Output
D (Differential)
150
300
500
200
300
450
200
300
450
200
300
450
ps
D (Single-Ended) 150 300 550 150 300 500 150 300 500 150 300 500
TSKEW
Within-Device Skew1
50
50
50
50
ps
TSKEW
Duty Cycle Skew2
tPLH - tPHL
±10
±10
±10
±10
ps
Vpp(AC) Minimum Input
Swing3
150
150
150
150
mV
VCMR
Common Mode
Range4
VCC
- 2.0
VCC
VCC
- 0.6 - 2.0
VCC
VCC
- 0.6 - 2.0
VCC
VCC
- 0.6 - 2.0
VCC
- 0.6
V
tr/tf
Rise/Fall Time
250
625 275
575 275
575 275
575 ps
20-80%
1. Within-device skew is defined as identical transitions on similar paths through a device.
2. Duty cycle skew is defined only for differential operation. The skews are measured from the crossover point of the inputs to the crossover point
of the outputs.
3. VPP is the minimum peak-to-peak differential input swing for which AC parameters are guaranteed.
4. The VCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within
the specified range and the peak-to-peak voltage lies between VPP (min) and 1V.
November 2006 * REV - 3
www.azmicrotek.com
3
Share Link: 