STK12C68-W45I(1999) Ver la hoja de datos (PDF) - Unspecified
Número de pieza
componentes Descripción
Fabricante
STK12C68-W45I
(Rev.:1999)
(Rev.:1999)
Unspecified
STK12C68-W45I Datasheet PDF : 12 Pages
| |||
STK12C68
ABSOLUTE MAXIMUM RATINGSa
Voltage on Input Relative to VSS . . . . . . . . . .–0.6V to (VCC + 0.5V)
Voltage on DQ0-7 or HSB . . . . . . . . . . . . . . . .–0.5V to (VCC + 0.5V)
Temperature under Bias. . . . . . . . . . . . . . . . . . . . . .–55°C to 125°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .–65°C to 150°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1W
DC Output Current (1 output at a time, 1s duration) . . . . . . . 15mA
Note a:
Stresses greater than those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device. This is a
stress rating only, and functional operation of the device at con-
ditions above those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rat-
ing conditions for extended periods may affect reliability.
DC CHARACTERISTICS
(VCC = 5.0V ± 10%)b, f
SYMBOL
ICC1c
PARAMETER
Average VCC Current
ICC2d
ICC3c
ICC4d
ISB1e
Average VCC Current during STORE
Average VCC Current at tAVAV = 200ns
5V, 25°C, Typical
Average VCAP Current during
AutoStore™ Cycle
Average VCC Current
(Standby, Cycling TTL Input Levels)
ISB2e
IILK
IOLK
VIH
VIL
VOH
VOL
VBL
TA
VCC Standby Current
(Standby, Stable CMOS Input Levels)
Input Leakage Current
Off-State Output Leakage Current
Input Logic “1” Voltage
Input Logic “0” Voltage
Output Logic “1” Voltage
Output Logic “0” Voltage
Logic “0” Voltage on HSB Output
Operating Temperature
COMMERCIAL
MIN
MAX
100
90
75
65
3
10
INDUSTRIAL
MIN
MAX
N/A
90
75
65
3
10
UNITS
mA
mA
mA
mA
mA
mA
2
2
mA
32
N/A
mA
27
28
mA
23
24
mA
20
21
mA
1.5
1.5
mA
±1
±1
µA
±5
±5
µA
2.2
VCC + .5
2.2
VCC + .5
V
VSS – .5
0.8
VSS – .5
0.8
V
2.4
2.4
V
0.4
0.4
V
0.4
0.4
V
0
70
– 40
85
°C
NOTES
tAVAV = 20ns
tAVAV = 25ns
tAVAV = 35ns
tAVAV = 45ns
All Inputs Don’t Care, VCC = max
W ≥ (V CC– 0.2V)
All Others Cycling, CMOS Levels
All Inputs Don’t Care
tAVAV = 20ns, E ≥ VIH
tAVAV = 25ns, E ≥ VIH
tAVAV = 35ns, E ≥ VIH
tAVAV = 45ns, E ≥ VIH
E ≥ (V CC – 0.2V)
All Others VIN ≤ 0.2V or ≥ (VCC – 0.2V)
VCC = max
VIN = VSS to VCC
VCC = max
VIN = VSS to VCC, E or G ≥ VIH
All Inputs
All Inputs
IOUT = – 4mA except HSB
IOUT = 8mA except HSB
IOUT = 3mA
Note b:
Note c:
Note d:
Note e:
Note f:
The STK12C68-20 requires VCC = 5.0V ± 5% supply to operate at specified speed.
IICCCC1
and
and
IICCCC3
are
are
dependent on output
the average currents
loading and
required for
cycle rate. The
the duration of
specified values are obtained with outputs
the respective STORE cycles (tSTORE ) .
unloaded.
E ≥2VIH will n4ot produce standby current levels until any nonvolatile cycle in progress has timed out.
VCC reference levels throughout this datasheet refer to VCCX if that is where the power supply connection is made, or VCAP if VCCX is con-
nected to ground.
AC TEST CONDITIONS
Input Pulse Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to 3V
Input Rise and Fall Times. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ≤ 5ns
Input and Output Timing Reference Levels . . . . . . . . . . . . . . . 1.5V
Output Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Figure 1
CAPACITANCEg (TA = 25°C, f = 1.0MHz)
SYMBOL
PARAMETER
MAX UNITS CONDITIONS
CIN
COUT
Input Capacitance
8
Output Capacitance
7
pF
∆V = 0 to 3V
pF
∆V = 0 to 3V
Note g: These parameters are guaranteed but not tested.
OUTPUT
255 Ohms
5.0V
480 Ohms
30 pF
INCLUDING
SCOPE AND
FIXTURE
Figure 1: AC Output Loading
July 1999
4-42
Share Link: