MC10EP08DTR2G(2016) Ver la hoja de datos (PDF) - ON Semiconductor
Número de pieza
componentes Descripción
Fabricante
MC10EP08DTR2G Datasheet PDF : 10 Pages
| |||
MC10EP08, MC100EP08
Table 4. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Condition 2
Rating
Unit
VCC
VEE
VI
Iout
PECL Mode Power Supply
NECL Mode Power Supply
PECL Mode Input Voltage
NECL Mode Input Voltage
Output Current
VEE = 0 V
VCC = 0 V
VEE = 0 V
VCC = 0 V
Continuous
Surge
VI ≤ VCC
VI ≥ VEE
6
V
−6
V
6
V
−6
50
mA
100
TA
Operating Temperature Range
Tstg Storage Temperature Range
qJA Thermal Resistance (Junction-to-Ambient)
0 lfpm
500 lfpm
SOIC−8 NB
SOIC−8 NB
−40 to +85
−65 to +150
190
130
°C
°C
°C/W
qJC Thermal Resistance (Junction-to-Case)
qJA Thermal Resistance (Junction-to-Ambient)
Standard Board
0 lfpm
500 lfpm
SOIC−8 NB
TSSOP−8
TSSOP−8
41 to 44
185
140
°C/W
°C/W
qJC Thermal Resistance (Junction-to-Case)
Tsol Wave Solder (Pb-Free)
Standard Board
< 2 to 3 sec @ 260°C
TSSOP−8
41 to 44
265
°C/W
°C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
Table 5. 10EP DC CHARACTERISTICS, PECL (VCC = 3.3 V, VEE = 0 V (Note 1))
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE Power Supply Current
20
28
36
20
30
38
20
32
38
mA
VOH Output HIGH Voltage (Note 2)
2165 2290 2415 2230 2355 2480 2290 2415 2540 mV
VOL Output LOW Voltage (Note 2)
1365 1490 1615 1430 1555 1680 1490 1615 1740 mV
VIH Input HIGH Voltage (Single-Ended)
2090
2415 2155
2480 2215
2540 mV
VIL Input LOW Voltage (Single-Ended)
1365
1690 1430
1755 1490
1815 mV
VIHCMR Input HIGH Voltage Common Mode
2.0
Range (Differential Configuration) (Note 3)
3.3 2.0
3.3 2.0
3.3
V
IIH
Input HIGH Current
IIL
Input LOW Current
D
D
0.5
−150
150
0.5
−150
150
0.5
−150
150 mA
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to −2.2 V.
2. All loading with 50 W to VCC − 2.0 V.
3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
www.onsemi.com
3
Share Link: 