M62021 Ver la hoja de datos (PDF) - MITSUBISHI ELECTRIC

Número de pieza

componentes Descripción

Fabricante

M62021

SYSTEM RESET IC WITH SWITCH FOR MEMORY BACK-UP

MITSUBISHI ELECTRIC  

MITSUBISHI<Dig.Ana.INTERFACE>

M62021L,P,FP

SYSTEM RESET IC WITH SWITCH FOR MEMORY BACK-UP

ABSOLUTE MAXIMUM RATINGS(Ta=25°C, unless otherwise noted)

Symbol

VIN

IOUT

Pd

K

Topr

Tstg

Parameter

Input voltage

Output current

Power dissipation

Thermal derating

Operating temperature

Storage temperature

Conditions

(Ta≥25°C)

Ratings

7

100

800(SIP)/625(DIP)/440(FP)

8(SIP)/6.25(DIP)/4.4(FP)

-20 ~ +75

-40 ~ +125

Unit

V

mA

mW

mW/°C

°C

°C

ELECTRICAL CHARACTERISTICS(Ta=25°C, unless otherwise noted)

Symbol

Parameter

Test conditions

Vs Detection voltage

VIN(At the change from H L)

∆Vs Hysteresis voltage

∆Vs=VSH-VSL

Vs/∆T Temperature coefficient of detection voltage

ICC Circuit current

IOUT=0mA

VIN=4V

VIN=5V

VDROP Difference between input and output voltage VIN=5V

IOUT=50mA

IOUT=80mA

VOH(Ct) Ct output voltage (high level)

VIN=5V(Note1)

VOL(Ct) Ct output voltage (low level)

VIN=4V(Note1)

VOH(RES) RES output voltage (high level)

VIN=4V(Note1)

Limits

Min.

Typ. Max.

4.2

4.4

4.6

50

100

200

0.005

2.0

4.0

7.5

12.0

0.125 0.25

0.2

0.4

4.5

5.0

0.02

0.1

3.5

4.0

Unit

V

mV

%/°C

mA

V

V

V

V

VOL(RES) RES output voltage (low level)

VOH(RES) RES output voltage (high level)

VOL(RES) RES output voltage (low level)

VOH(CS) CS output voltage (high level)

VOL(CS) CS output voltage (low level)

IR Backup Di leak current

VF Backup Di forward direction voltage

tpd Delay time

td Response time

VOPL(RES) RES limit voltage of operation

VIN=5V

VIN=5V(Note1)

(Note1)

ISINK=1mA

VIN=4V

(Note1)

ISINK=1mA

VIN=4V (Note2)

VIN=0V,VBAT=3V (Note2)

VIN=5V

(Note1)

ISINK=1mA

VBAT=3V

VIN=5V

VIN=0V

IF=10µA

VIN=0V 5V,Ct=4.7µF

VIN=5V 4V

(Note 3)

0.02

0.05

0.2

V

4.5

5.0

V

0.02

0.05

0.2

V

3.50

3.57

V

2.40

2.47

0.08

0.1

0.3

V

±0.5

±0.5

µA

0.54

0.6

V

10

27

55

ms

5.0

25.0

µs

0.65

V

Note 1.Regarding conditions to measure VOH and VOL,voltage values are to be generated by internal resistance only and no external resistor is used.

2.These values are produced inserting an external resistor,RCS=1MΩ,between the CS pin and GND.

3.With no external resistor (10kΩ internal resistance only)

MITSUBISHI

ELECTRIC

( 2 /9)

Share Link: