HIN230 thru HIN241
Ordering Information
PART
NUMBER
HIN230CB
HIN230IB
HIN231CB
HIN231CP
HIN231IB
HIN231IP
HIN232CP
HIN232CB
HIN232IP
HIN232IB
HIN233CP
HIN234CB
HIN234IB
HIN235CP
HIN236CP
HIN236CB
HIN236IP
HIN236IB
TEMP.
RANGE (oC)
PACKAGE
0 to 70 20 Ld SOIC
-40 to 85 20 Ld SOIC
0 to 70 16 Ld SOIC
0 to 70 14 Ld PDIP
-40 to 85 16 Ld SOIC
-40 to 85 14 Ld PDIP
0 to 70 16 Ld PDIP
0 to 70 16 Ld SOIC
-40 to 85 16 Ld PDIP
-40 to 85 16 Ld SOIC
0 to 70 20 Ld PDIP
0 to 70 16 Ld SOIC
-40 to 85 16 Ld SOIC
0 to 70 24 Ld PDIP
0 to 70 24 Ld PDIP
0 to 70 24 Ld SOIC
-40 to 85 24 Ld PDIP
-40 to 85 24 Ld SOIC
PKG. NO.
M20.3
M20.3
M16.3
E14.3
M16.3
E14.3
E16.3
M16.3
E16.3
M16.3
E20.3
M16.3
M16.3
E24.6
E24.3
M24.3
E24.3
M24.3
PART
NUMBER
TEMP.
RANGE (oC)
PACKAGE
PKG. NO.
HIN237CP
0 to 70 24 Ld PDIP
E24.3
HIN237CB
0 to 70 24 Ld SOIC
M24.3
HIN237IP
-40 to 85 24 Ld PDIP
E24.3
HIN237IB
-40 to 85 24 Ld SOIC
M24.3
HIN238CP
0 to 70 24 Ld PDIP
E24.3
HIN238CB
0 to 70 24 Ld SOIC
M24.3
HIN238IP
-40 to 85 24 Ld PDIP
E24.3
HIN238IB
-40 to 85 24 Ld SOIC
M24.3
HIN239CB
0 to 70 24 Ld SOIC
M24.3
HIN239CP
0 to 70 24 Ld PDIP
E24.3
HIN239IB
-40 to 85 24 Ld SOIC
M24.3
HIN240CN
0 to 70 44 Ld MQFP
Q44.10X10
HIN240IN
-40 to 85 44 Ld MQFP
Q44.10X10
HIN241CB
0 to 70 28 Ld SOIC
M28.3
HIN241IB
-40 to 85 28 Ld SOIC
M28.3
HIN241CA
0 to 70 28 Ld SSOP
M28.209
HIN241IA
-40 to 85 28 Ld SSOP
M28.209
NOTE: Many of the surface mount devices are available on tape and
reel; add -T to suffix.
Pin Descriptions
PIN
VCC
V+
FUNCTION
Power Supply Input 5V ±10%.
Internally generated positive supply (+10V nominal), HIN231 and HIN239 require +7.5V to +13.2V.
V-
Internally generated negative supply (-10V nominal).
GND
C1+
C1-
C2+
Ground lead. Connect to 0V.
External capacitor (+ terminal) is connected to this lead.
External capacitor (- terminal) is connected to this lead.
External capacitor (+ terminal) is connected to this lead.
C2-
TIN
TOUT
RIN
ROUT
EN
SHUTDOWN
External capacitor (- terminal) is connected to this lead.
Transmitter Inputs. These leads accept TTL/CMOS levels. An internal 400kΩ pull-up resistor to VCC is connected to each lead.
Transmitter Outputs. These are RS-232 levels (nominally ±10V).
Receiver Inputs. These inputs accept RS-232 input levels. An internal 5kΩ pull-down resistor to GND is connected to each input.
Receiver Outputs. These are TTL/CMOS levels.
Enable input. This is an active low input which enables the receiver outputs. With EN = 5V, the outputs are placed in a high
impedance state.
Shutdown Input. With SHUTDOWN = 5V, the charge pump is disabled, the receiver outputs are in a high impedance state
and the transmitters are shut off.
NC
No Connect. No connections are made to these leads.
3-2