DS2Y-S-DC24V-TB Ver la hoja de datos (PDF) - Panasonic Corporation
Número de pieza
componentes Descripción
Fabricante
DS2Y-S-DC24V-TB Datasheet PDF : 3 Pages
| |||
DS2Y
RATING
1. Coil data
Single side stable type
Nominal coil
voltage
Pick-up voltage
(at 20°C 68°F)
3 V DC
5 V DC
6 V DC
9 V DC
12 V DC
24 V DC
48 V DC
70%V or less of
nominal voltage
(Initial)
Drop-out voltage
(at 20°C 68°F)
10%V or more of
nominal voltage
(Initial)
Nominal operating
current
[±10%] (at 20°C 68°F)
66.7 mA
40 mA
33.3 mA
22.2 mA
16.7 mA
8.3 mA
6.3 mA
Coil resistance
[±10%] (at 20°C 68°F)
45 Ω
125 Ω
180 Ω
405 Ω
720 Ω
2,880 Ω
7,680 Ω
Nominal operating
power
200 mW
300 mW
Max. applied voltage
(at 50°C 122°F)
200%V of
nominal voltage
2. Specifications
Characteristics
Contact
Rating
Electrical
characteristics
Item
Arrangement
Initial contact resistance, max.
Contact material
Max. switching power
Max. switching voltage
Max. switching current
Max. carrying current
Minimum operating power
Nominal operating power
Insulation resistance (Initial)
Breakdown voltage
(Initial)
Between open contacts
Between contact sets
Between contact and coil
FCC surge breakdown voltage between contacts
and coil
Temperature rise (at 20°C 68°F)
Operate time [Set time] (at 20°C 68°F)
Mechanical
characteristics
Expected life
Conditions
Unit weight
Release time [Reset time] (at 20°C 68°F)
Shock resistance
Vibration resistance
Mechanical
Electrical
Functional
Destructive
Functional
Destructive
Conditions for operation, transport and storage*
Max. operating speed (at rated load)
Specifications
2 Form C
Max. 50 mΩ (By voltage drop 6 V DC 1A)
Ag+Au clad
60 W, 62.5 VA (resistive load)
220 V DC, 250 V AC
2A
3A
Approx. 98 mW (147 mW: 48 V)
Approx. 200 mW (300 mW: 48 V)
Min. 100MΩ (at 500V DC)
Measurement at same location as “Initial breakdown voltage” section.
750 Vrms for 1min. (Detection current: 10mA.)
1,000 Vrms for 1min. (Detection current: 10mA.)
1,000 Vrms for 1min. (Detection current: 10mA.)
1,500 V
Max. 65°C with nominal coil voltage across coil and at nominal switching capacity
Approx. 4 ms [approx. 3 ms]
(Nominal coil voltage applied to the coil, excluding contact bounce time.)
Approx. 3 ms [approx. 3 ms]
(Nominal coil voltage applied to the coil, excluding contact bounce time.) (without diode)
Min. 490 m/s2 (Half-wave pulse of sine wave: 11 ms; detection time: 10μs.)
Min. 980 m/s2 (Half-wave pulse of sine wave: 6 ms.)
10 to 55 Hz at double amplitude of 3.3 mm (Detection time: 10μs.)
10 to 55 Hz at double amplitude of 5 mm
Min. 108
Min. 5×105 (1 A 30 V DC), Min. 105 (2 A 30 V DC)
Ambient temperature: –40°C to +70°C –40°F to +158°F
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
60 cpm
Approx. 4g .14oz
Notes: *1 This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the
actual load. TX/TX-S/TX-D relay AgPd contact type are available for low level load switching (10V DC, 10mA max. level).
*2 Half-wave pulse of sine wave: 11ms; detection time: 10μs
*3 Refer to “AMBIENT ENVIRONMENT” in GENERAL APPLICATION GUIDELINES.
–2–
ASCTB16E 201407-T
Share Link: 