LTC1647-3 Ver la hoja de datos (PDF) - Linear Technology

Número de pieza

componentes Descripción

Fabricante

LTC1647-3

Dual Hot Swap Controllers

Linear Technology 

LTC1647-1/LTC1647-2/LTC1647-3

APPLICATIO S I FOR ATIO

The circuit breaker trip voltage has a tolerance of 20%;

combined with a 5% sense resistor, the total tolerance is

25%. Therefore, calculate R1 based on a trip current ITRIP

of no less than 125% of the maximum operating current.

Do not neglect the effect of ripple current, which adds to

the maximum DC component of the load current. Ripple

current may arise from any of several sources, but the

worst offenders are switching supplies.

A switching regulator on the load side will attempt to draw

some ripple current from the backplane and this current

passes through the sense resistor. Similarly, output ripple

from a switching regulator supplying the backplane will

flow through the sense resistor and into the load capacitor.

Minimize the effects of ripple current by either filtering the

VOUT line or adding an RC filter to the SENSE pin. A series

inductance of 1µH to 10µH inserted between Q1 and CLOAD

is adequate ripple current suppression in most cases.

Alternatively, a filter, consisting of R3 and C3(Figure 3),

simply filters the ripple component from the SENSE pin at

the expense of response time. The added delay is given by

tDELAY = – R3•C3•ln[1 – (VCB/R1 – IAV)/(IPK – IAV)]

VCC

FAULT

R1

0.01Ω

Q1

IRF7413

+

VOUT

CLOAD

R3

R2

10k

10Ω

1

15

13

VCC

SENSE GATE

2

ON

ON1

3

LTC1647-3

FAULT

8

GND

C1

10nF

1647-1/2/3 F01

Figure 1. Supply Control Circuitry

VON

VCC – VSENSE

VGATE

tFAULT

tRESET

VFAULT

1647-1/2/3 F02

Figure 2. Current Fault Timing

R1

Q1

0.01Ω

IRF7413

VCC

+

VOUT

CLOAD

C3

R3

R2

10nF 1.5k

10Ω

C1

10nF

IPK = 7.5A

IAV = 2.5A

ITRIP = VCB/R1 = 5A

tDELAY = 10µs

VCC

SENSE GATE

LTC1647

1647-1/2/3 F03

Figure 3. Filtering Current Ripple/Glitches

Power MOSFET Selection

Power MOSFETs are classified into two catagories: stan-

dard MOSFETs (RDS(ON) specified at VGS = 10V) and logic-

level MOSFETs (RDS(ON) specified at VGS = 5V). The

absolute maximum rating for VGS is typically 20V for

standard MOSFETs. The maximum rating for logic-level

MOSFETs is lower and ranges from 8V to 16V depending

on the manufacturer and specific part number. Some

logic-level MOSFETs have a 20V maximum VGS rating. The

LTC1647 is primarily targeted for standard MOSFETs; low

supply voltage applications should use logic-level

MOSFETs. GATE overdrive as a function of VCC is illus-

trated in the Typical Performance Curves. If lower GATE

overdrive is desired, connect a diode in series with a Zener

between GATE and VCC or between GATE and VOUT as

shown in Figure 4.

The RDS(ON) of the external pass transistor must be low to

make VDS a small percentage of VCC. At VCC = 3.3V, VDS +

VCB = 0.1V yields 3% error at maximum load current. This

restricts the choice of MOSFETs to very low RDS(ON). At

higher VCC voltages, the RDS(ON) requirement can be

relaxed. MOSFET package dissipation (PD and TJ) may

restrict the value of RDS(ON).

R1

Q1

VCC

VOUT

D2

D1* 1N4148

D2

1N4148 D4*

*USER SELECTED VOLTAGE CLAMP

1N4688 (5V)

1N4692 (7V): LOGIC-LEVEL MOSFET

1N4695 (9V)

1N4702 (15V): STANDARD-LEVEL MOSFET

1647-1/2/3 F04

Figure 4. Optional Gate Clamp

10

Share Link: