VO3052 Ver la hoja de datos (PDF) - Vishay Semiconductors
Número de pieza
componentes Descripción
Fabricante
VO3052
Vishay Semiconductors
VO3052 Datasheet PDF : 11 Pages
| |||
www.vishay.com
VO3052, VO3053
Vishay Semiconductors
ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
PART SYMBOL MIN.
TYP.
MAX.
UNIT
INPUT
Reverse current
Forward voltage
OUTPUT
VR = 6 V
IF = 30 mA
IR
-
-
10
μA
VF
-
1.2
1.5
V
Leakage with LED off, either direction
Critical rate of rise off-state voltage
COUPLER
VDRM = 600 V
VD = 400 V
IDRM
-
10
500
nA
dV/dtcr
1500
2000
-
V/μs
LED trigger current,
current required to latch output
Peak on-state voltage,
either direction
Holding current, either direction
Coupling capitance
VO3053
IFT
VO3052
IFT
ITM = 100 mA peak,
IF = rated IFT
VTM
IH
10 kHz
CIO
-
-
5
mA
-
-
10
mA
-
1.7
3
V
-
200
-
μA
-
0.4
-
pF
Note
• Typical values are characteristics of the device and are the result of engineering evaluations. Typical values are for information only and are
not part of the testing requirements.
SAFETY AND INSULATION RATINGS
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
Climatic classification
According to IEC 68 part 1
55 / 100 / 21
Pollution degree
According to DIN VDE 0109
2
Comparative tracking index
Insulation group IIIa
CTI
175
Maximum rated withstanding isolation voltage
Tested withstanding isolation voltage
Maximum transient isolation voltage
Maximum repetitive peak isolation voltage
Isolation resistance
Output safety power
Input safety current
Input safety temperature
Creepage distance
Clearance distance
According to UL1577, t = 1 min
According to UL1577, t = 1 s
According to DIN EN 60747-5-5
According to DIN EN 60747-5-5
Tamb = 25 °C, VIO = 500 V
Tamb = 100 °C, VIO = 500 V
DIP-6, SMD-6 with option 7 and 9
VISO
VISO
VIOTM
VIORM
RIO
RIO
PSO
ISI
TS
4420
5300
8000
890
≥ 1012
≥ 1011
500
250
175
≥7
≥7
VRMS
VRMS
Vpeak
Vpeak
Ω
Ω
mW
mA
°C
mm
mm
Creepage distance
Clearance distance
DIP-6, 400 mil, option 6
≥8
mm
≥8
mm
Insulation thickness
DTI
≥ 0.4
mm
Input to output test voltage, method A
VIORM x 1.6 = VPR, 100 % sample test
with tM = 10 s, partial discharge < 5 pC
VPR
1669
Vpeak
Note
• As per IEC 60747-5-5, § 7.4.3.8.2, this optocoupler is suitable for “safe electrical insulation” only within the safety ratings. Compliance with
the safety ratings shall be ensured by means of protective circuits
Rev. 2.2, 12-May-17
3
Document Number: 83749
For technical questions, contact: optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Share Link: