TLP716 Ver la hoja de datos (PDF) - Toshiba
Número de pieza
componentes Descripción
Fabricante
TLP716 Datasheet PDF : 6 Pages
| |||
Absolute Maximum Ratings (Ta=25°C)
TLP716
CHARACTERISTIC
SYMBOL
RATING
UNIT
Forward Current (Ta ≤ 85°C)
Forward Current Derating (Ta > 85°C)
Peak Transient Forward Current
(Note1)
Reverse Voltage
Diode power dissipation
Diode power dissipation derating (Ta >85°C)
Junction Temperature
Output Current (Ta ≤ 85°C)
Output Current Derating (Ta > 85°C)
Output Voltage (VO ≤ VCC)
Supply Voltage
Power Dissipation (Ta ≤ 85°C)
Power Dissipation Derating (Ta > 85°C)
Junction Temperature
Operating Temperature Range
Storage Temperature Range
Lead Solder Temperature(10 s)
Isolation Voltage (AC, 60 s, R.H. ≤ 60 %)
(Note2)
IF
∆IF/∆Ta
IFPT
VR
PD
∆PD/∆Ta
Tj
IO
∆IO/∆Ta
VO
VCC
PC
∆PC/∆Ta
Tj
Topr
Tstg
Tsol
BVS
20
-0.5
1
5
40
-1.0
125
10
-0.25
-0.5 to 6
-0.5 to 6
40
-1.0
125
-40 to 100
-55 to 125
260
5000
mA
mA/°C
A
V
mW
mW/°C
°C
mA
mA/°C
V
V
mW
mW/°C
°C
°C
°C
°C
Vrms
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings and the operating ranges.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test
report and estimated failure rate, etc.).
Note 1: Pulse width PW ≤ 1 μs, 300 pps.
Note 2: Device Considered a two terminal device: pins 1, 2 and 3 shorted together and pins 4, 5 and 6 shorted
together.
Recommended Operating Conditions
CHARACTERISTIC
SYMBOL MIN TYP. MAX UNIT
Input Current, ON
IF(ON)
8
12
18
mA
Input Voltage, OFF
VF(OFF)
0
—
0.8
V
Supply Voltage (Note1)(Note2)(Note 3)
VCC
4.5
5
5.5
V
Note: Recommended operating conditions are given as a design guideline to obtain expected performance of the
device. Additionally, each item is an independent guideline respectively. In developing designs using this
product, please confirm specified characteristics shown in this document.
Note 1: This item denotes operating ranges, not meaning of recommended operating conditions.
Note 2: The detector of this product requires a power supply voltage (VCC) of 4.5 V or higher for stable operation. If
the VCC is lower than this value, an ICC may increase, or an output may be unstable. Be sure to use the
product after checking the supply current, and the operation of a power-on/-off.
Note 3: A ceramic capacitor (0.1 μF) should be connected from pin 6 to pin 4 to stabilize the operation of the high
gain linear amplifier. Failure to provide the bypassing may impair the switching property. The total lead
length between capacitor and coupler should not exceed 1 cm.
© 2019
2
Toshiba Electronic Devices & Storage Corporation
2019-06-03
Share Link: 