STK402-100 Ver la hoja de datos (PDF) - SANYO -> Panasonic
Número de pieza
componentes Descripción
Fabricante
STK402-100 Datasheet PDF : 6 Pages
| |||
STK402-070
Series Organization
These products are organized as a series based on their output capacity.
Type No.
Item
STK402-020 STK402-030 STK402-040 STK402-050 STK402-070 STK402-090 STK402-100 STK402-120
Output 1 (10%/1 kHz)
20 W + 20 W 30 W + 30 W 40 W + 40 W 45 W +45 W 60 W + 60 W 80 W + 80 W 100 W + 100 W 120 W + 120 W
Output 2 (0.4%/20 Hz to 20 kHz) 15 W + 15 W 20 W + 20 W 25 W + 25 W 30 W + 30 W 40 W + 40 W 50 W + 50 W 60 W + 60 W 80 W + 80 W
Maximum supply voltage
(No signal)
±30 V
±34 V
±38 V
±40 V
±50 V
±54 V
±57 V
±65 V
Maximum supply voltage
(6 Ω)
±28 V
±32 V
±36 V
±38 V
±44 V
±47 V
±50 V
±57 V
Recommended supply voltage
(6 Ω)
±19 V
±22 V
±25 V
±26.5 V
±30 V
±32 V
±35 V
±39 V
Package
46.6 mm × 25.5 mm × 8.5 mm
59.2 mm × 31.0 mm × 8.5 mm
Specifications
Maximum Ratings at Ta = 25°C
Parameter
Maximum supply voltage (No signal)
Maximum supply voltage
Thermal resistance
Junction temperature
Operating IC substrate temperature
Storage temperature
Allowable load shorted time
Symbol
Conditions
VCC max(0)
VCC max(1)
θj-c
RL = 6 Ω
Per power transistor
Tj max
Tc max
Both the Tj max and the Tc max conditions must be met.
Tstg
ts
VCC = ±30.0 V, RL = 6 Ω, f = 50 Hz, PO = 40 W
Ratings
±50
±44
3.2
150
125
–30 to +125
0.3
Unit
V
V
°C/W
°C
°C
°C
s
Operating Characteristics at Ta = 25°C, RL = 6 Ω (noninductive load), Rg = 600 Ω, VG = 30 dB
Parameter
Output power
(continuous output)
Total harmonic distortion
Frequency characteristics
Input impedance
Output noise voltage *2
Quiescent current
Neutral voltage
Symbol
PO (1)
PO (2)
THD (1)
THD (2)
fL, fH
ri
VNO
ICCO
VN
VCC (V) f (Hz)
±30.0 20 to 20 k
±30.0
1k
±30.0 20 to 20 k
±30.0
1k
±30.0
±30.0
1k
±36.0
±36.0
±36.0
Conditions*1
PO (W) THD (%)
0.4
10
1.0
5.0
1.0
1.0
VG = 30 dB
VG = 30 dB
+0 –3 dB
Rg = 2.2 kΩ
min
38
Ratings
typ
40
60
0.01
20 to 50 k
55
10
40
–70
0
Unit
max
W
0.4
%
Hz
kΩ
1.2 mVrms
80 mA
+70 mV
Notes: 1. Unless otherwise noted, use a constant-voltage supply for the power supply used during inspection.
2. The output noise voltage values shown are peak values read with a VTVM. However, an AC stabilized (50 Hz) power supply should be used to
minimize the influence of AC primary side flicker noise on the reading.
Use the transformer power supply circuit stipulated in the figure below for output noise voltage measurement.
3. Use the transformer power supply circuit stipulated in the figure below for allowable load shorted time measurement.
DBA40C
10000µF
500Ω
+VCC
500Ω
10000µF
--VCC
Stipulated Transformer Power Supply (MG-200 equivalent)
No. 7047-2/6
Share Link: 