LT1130A Ver la hoja de datos (PDF) - Linear Technology
Número de pieza
componentes Descripción
Fabricante
LT1130A Datasheet PDF : 12 Pages
| |||
LT1130A/LT1140A Series
U
PACKAGE DESCRIPTIO Dimensions in inches (millimeters) unless otherwise noted.
0.600 – 0.625
(15.240 – 15.875)
0.150 ± 0.005
(3.810 ± 0.127)
0.045 – 0.065
(1.143 – 1.651)
0.009 – 0.015
(0.229 – 0.381)
0.015
(0.381)
MIN
+0.035
0.625 –0.015
( ) 15.87
+0.889
–0.381
0.125
(3.175)
MIN
0.035 – 0.080
(0.889 – 2.032)
0.100 ± 0.010
(2.540 ± 0.254)
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
NW Package
28-Lead PDIP (Wide 0.600)
(LTC DWG # 05-08-1520)
0.070
(1.778)
TYP
1.455*
(36.957)
MAX
28 27 26 25 24 23 22 21 20 19 18 17 16 15
0.018 ± 0.003
(0.457 ± 0.076)
0.505 – 0.560*
(12.827 – 14.224)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
N28 1197
0.291 – 0.299**
(7.391 – 7.595)
0.010
(0.254
–
–
0.029
0.737)
×
45°
SW Package
20-Lead Plastic Small Outline (Wide 0.300)
(LTC DWG # 05-08-1620)
0.093 – 0.104
(2.362 – 2.642)
0.037 – 0.045
(0.940 – 1.143)
0.496 – 0.512*
(12.598 – 13.005)
20 19 18 17 16 15 14 13 12 11
0° – 8° TYP
0.050
0.009 – 0.013
(0.229 – 0.330)
NOTE:
NOTE 1
0.016 – 0.050
(0.406 – 1.270)
(1.270)
TYP
0.014 – 0.019
(0.356 – 0.482)
TYP
1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS.
THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
NOTE 1
0.004 – 0.012
(0.102 – 0.305)
0.394 – 0.419
(10.007 – 10.643)
1 2 3 4 5 6 7 8 9 10
S20 (WIDE) 0396
0.291 – 0.299**
(7.391 – 7.595)
0.010
(0.254
–
–
0.029
0.737)
×
45°
SW Package
24-Lead Plastic Small Outline (Wide 0.300)
(LTC DWG # 05-08-1620)
0.093 – 0.104
(2.362 – 2.642)
0.037 – 0.045
(0.940 – 1.143)
0.598 – 0.614*
(15.190 – 15.600)
24 23 22 21 20 19 18 17 16 15 14 13
0° – 8° TYP
0.050
0.009 – 0.013
(0.229 – 0.330)
NOTE:
NOTE 1
0.016 – 0.050
(0.406 – 1.270)
(1.270)
TYP
0.014 – 0.019
(0.356 – 0.482)
TYP
1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS.
THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
NOTE 1
0.004 – 0.012
(0.102 – 0.305)
0.394 – 0.419
(10.007 – 10.643)
1 2 3 4 5 6 7 8 9 10 11 12
S24 (WIDE) 0996
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
11
Share Link: 