PI5C16215C Ver la hoja de datos (PDF) - Pericom Semiconductor

Número de pieza

componentes Descripción

Fabricante

PI5C16215C

20-Bit, Hot Insertion, BusSwitch with Precharged Outputs & Undershoot Protection

Pericom Semiconductor 

PI5C16215C

20-Bit, Hot Insertion, BusSwitch with

112233445566778899001122334455667788990011223344556677889900112211223344556677889900112233445566778899001122334455667788990011221122334455667788990011223344556677P88r9900e11c2233h44a5566r77g8899e00d1122O112233u44t55p6677u8899t00s11&223344U556677n88d9900e11r2233s44h5566o77o8899t00P1122r11o2233t44e55c6677t88io9900n1122

Absolute Maximum Ratings Over Free-Air Temperature Range

(Above which the useful life may be impaired. For user guidelines, not tested.)

Storage Temperature ..................................... –65°Cto+150°C

Supply Voltage Range ........................................ –0.5Vto+7V

DC Input Voltage(1) ...................................................... –0.5V to +7V

Input Clamp Current, IIK (VI <0) ................................. –50mA

DC Output Current ....................................................... 120mA

Power Dissipation(2) .................................................................... 0.5W

Note:

Stresses greater than those listed under MAXIMUM RATINGS

may cause permanent damage to the device. This is a stress rating

only and functional operation of the device at these or any other

conditions above those indicated in the operational sections of this

specification is not implied. Exposure to absolute maximum rating

conditions for extended periods may affect reliability.

Notes:

1. The input and output negative-voltage ratings may be exceeded

if the input and output clamp-current ratings are observed.

2. The maximum package power dissipation is calculated using a

junction temperatue of 150°C and a board trace length of 750

mils.

Recommended Operating Conditions (Over Recommended Operating Free-air Temperature Range)

Parameter

Description

Min.

Max.

Units

VCC

BIASV

VIH

Supply voltage

Supply voltage

High-Level input voltage

4

5.5

1.3

VCC

V

2

VIL

Low-level input voltage

0.8

TA

Operating free-air temperature

–40

85

°C

Electrical Characteristics (Over Recommended Operating Free-air Temperature Range)

Parameter

Test Conditions

Min. Typ= Max. Units

VIK

VCC = 4.5V

II = –18mA

–1.8 V

II

VCC = 5.5V

VI = 5.5V or GND

±5 µA

IO

VCC = 4.5V

BIASV = 2.4V VO = 0

0.25

mA

ICC

∆ICCE Control pins

VCC = 5.5V

VCC = 5.5V

IO = 0

VI = VCC or GND

One input at 3.4V, Other at VCC or GND

100 µA

2.5 mA

CI Control pins

CO (OFF)

rON*

VI =3V or 0

VO =3V or 0

Switch Off

VCC = 4V VI = 2.4V

VI = 0,

VCC = 4.5V VI = 0,

II = 15mA

II = 64mA

II = 30mA

3.5

pF

4.5

9

20

5.5

8

ohm

5

8

VI = 2.4V

II = 15mA

9

15

Notes:

* Measured by the voltage drop between the A and B terminals at the indicated current through the switch.

On-state resistance is determined by the lower of the voltages of the two (A or B) terminals.

E This is the increase in supply current for each input that is at the specified TTL voltage level rather the VCC or GND.

= All typical values are at VCC = 5V, TA = 25°C.

2

PS8369B

12/15/01

Share Link: