NTE1416 Ver la hoja de datos (PDF) - NTE Electronics
Número de pieza
componentes Descripción
Fabricante
NTE1416 Datasheet PDF : 5 Pages
| |||
Electrical Characteristics (Cont’d): (TA = +25°C, VCC = 12V, Note 2 unless otherwise specified)
Parameter
Symbol
Test Conditions
Min Typ Max Unit
Phase Error
∆Φ Burst signal input 0.7Vp–p,
Phase error to 100Hz of burst
frequency variation
–
1.5
3.0 degree
/100Hz
APC Pull–in Frequency Range
fp Burst signal input 0.7Vp–p,
Measured by changing the burst
frequency
±350 ±500
–
Hz
Variable Range of Tint
∆Θ1 Burst signal input 0.7Vp–p,
Tint; max min, manual,
±37 ±45
Tint center, Range from 0 as a standard
±53 degree
Variable Range of Tint at Auto
∆Θ2 Burst signal input 0.7Vp–p,
Tint; max min, auto
±12 ±17
Tint center, Range from 0 as standard
±22 degree
B–Y Output Voltage
eo1 Dem. input 0.2Vp–p, f = 3.59MHz,
1.5 2.0
2.5
Vp–p
Bright VR was set to be V26 = 3.5V (DC)
No blanking input
Ratio of R–Y to B–Y
R/B Dem. input 0.2Vp–p, f = 3.59MHz,
0.86 0.94
R Output Voltage/eo1
Bright VR was set to be V26 = 3.5V (DC)
No blanking input
1.04
times
Ratio of G–Y to B–Y
G/B Dem. input 0.2Vp–p, f = 3.59MHz,
0.25 0.30
G Output Voltage/eo1
Bright VR was set to be V26 = 3.5V (DC)
No blanking input
0.35
times
Relative Output phase
G–Y to R–Y
∠R Dem. input 0.2Vp–p, f = 3.59MHz,
B = 0 degree, phase difference
94 97.5 102 degree
Bright VR was set to be V26 = 3.5V(DC)
No blanking input
Relative Output phase
G–Y to B–Y
∠G Dem. input 0.2Vp–p, f = 3.59MHz,
B = 0 degree, phase difference
228 235
Bright VR was set to be V26 = 3.5V(DC)
No blanking input
242 degree
Maximum Color Difference
Output Voltage
eo2 Dem. input 1.2Vp–p, f = 3.59MHz,
4.8 5.7
–
Vp–p
Bright VR was set to be V26 = 3.5V (DC)
No blanking input
Residual Carrier
ecar No signal input, Output; 3.58MHz each, –
–
100
mVp–p
Carrier leak component,
Bright VR was set to be V26 = 3.5V(DC),
No blanking input
Demodulation Frequency
Characteristic
eof Attenuation factor of demodulation
output at f = 500kHz,
Dem. input 0.2Vp–p, f = 3.08MHz,
Assuming the output at f = 10kHz
is 0 dB
–1.5 –0.9 –0.4
dB
Overall Color Difference Output
Voltage
Overall Color Difference Output
Variable Range by Contrast
eo3
∆eoc
Rainbow color bar signal input
150mVp–p, Color auto center,
Contrast max, in R output
1.0 1.7
2.4
Vp–p
3.4 3.85 4.3
Vp–p
Color Killer Tolerance
ek Burst input Voltage at Pin13
150mVp–p = 0dB,
Attenuation value in operating
the killer
–27 –32 –40
dB
Note 2. Color control is manual state and tint is center for the items not specifically specified.
Share Link: 