NCP1011APL065R2G Ver la hoja de datos (PDF) - ON Semiconductor

Número de pieza

componentes Descripción

Fabricante

NCP1011APL065R2G

Self-Supplied Monolithic Switcher for Low Standby-Power Offline SMPS

ON Semiconductor 

NCP1010, NCP1011,

NCP1012, NCP1013,

NCP1014

Self- Supplied Monolithic

Switcher for Low Standby--

Power Offline SMPS

The NCP101X series integrates a fixed--frequency current--mode

http://onsemi.com

controller and a 700 V MOSFET. Housed in a PDIP-- 7,

PDIP--7 Gull Wing, or SOT--223 package, the NCP101X offers

MARKING DIAGRAMS

4

everything needed to build a rugged and low--cost power supply,

including soft--start, frequency jittering, short--circuit protection,

skip--cycle, a maximum peak current setpoint and a Dynamic

4

SOT--223

CASE 318E

1

ST SUFFIX

AYW

101xy G

G

Self--Supply (no need for an auxiliary winding).

Unlike other monolithic solutions, the NCP101X is quiet by nature:

1

during nominal load operation, the part switches at one of the available

frequencies (65 -- 100 -- 130 kHz). When the current setpoint falls

below a given value, e.g. the output power demand diminishes, the IC

automatically enters the so--called skip--cycle mode and provides

excellent efficiency at light loads. Because this occurs at typically 1/4

of the maximum peak value, no acoustic noise takes place. As a result,

8

1

PDIP--7

CASE 626A

AP SUFFIX

P101xAPyy

AWL

YYWWG

1

standby power is reduced to the minimum without acoustic noise

generation.

Short--circuit detection takes place when the feedback signal fades

away, e.g. in true short--circuit conditions or in broken Optocoupler

cases. External disabling is easily done either simply by pulling the

PDIP--7

(Gull Wing)

1xAPLyyy

CASE 626AA

AWL

1

APL SUFFIX

YYWWG

1

feedback pin down or latching it to ground through an inexpensive

SCR for complete latched--off. Finally soft--start and frequency

jittering further ease the designer task to quickly develop low--cost and

robust offline power supplies.

For improved standby performance, the connection of an auxiliary

winding stops the DSS operation and helps to consume less than

100 mW at high line. In this mode, a built--in latched overvoltage

protection prevents from lethal voltage runaways in case the

Optocoupler would brake. These devices are available in economical

x

= Current Limit (0, 1, 2, 3, 4)

y

= Oscillator Frequency

A (65 kHz), B (100 kHz), C (130 kHz)

yy

= 06 (65 kHz), 10 (100 kHz), 13 (130 kHz)

yyy = 065, 100, 130

A

= Assembly Location

WL, L = Wafer Lot

YY, Y = Year

WW, W = Work Week

G or G = Pb--Free Package

(Note: Microdot may be in either location)

8--pin dual--in--line and 4--pin SOT--223 packages.

ORDERING INFORMATION

Features

 Built--in 700 V MOSFET with Typical RDSon of 11 Ω

and 22 Ω

 Large Creepage Distance Between High--Voltage Pins

 Current--Mode Fixed Frequency Operation:

65 kHz – 100 kHz -- 130 kHz

 Skip--Cycle Operation at Low Peak Currents Only:

No Acoustic Noise!

 Dynamic Self--Supply, No Need for an Auxiliary

Winding

 Internal 1.0 ms Soft--Start

 Latched Overvoltage Protection with Auxiliary

Winding Operation

 Frequency Jittering for Better EMI Signature

See detailed ordering and shipping information in the package

dimensions section on page 21 of this data sheet.

 Auto--Recovery Internal Output Short--Circuit

Protection

 Below 100 mW Standby Power if Auxiliary Winding

is Used

 Internal Temperature Shutdown

 Direct Optocoupler Connection

 SPICE Models Available for TRANsient Analysis

 These are Pb--Free and Halide--Free Devices

Typical Applications

 Low Power AC/DC Adapters for Chargers

 Auxiliary Power Supplies (USB, Appliances,TVs, etc.)

 Semiconductor Components Industries, LLC, 2010

1

December, 2010 -- Rev. 22

Publication Order Number:

NCP1010/D

Share Link: