MX29F001B Ver la hoja de datos (PDF) - Macronix International

Número de pieza

componentes Descripción

Fabricante

MX29F001B

1M-BIT [128K x 8] CMOS FLASH MEMORY

Macronix International 

MX29F001T/B

READ/RESET COMMAND

The read or reset operation is initiated by writing the read/

reset command sequence into the command register.

Microprocessor read cycles retrieve array data. The de-

vice remains enabled for reads until the command regis-

ter contents are altered.

If program-fail or erase-fail happen, the write of F0H will

reset the device to abort the operation. A valid com-

mand must then be written to place the device in the

desired state.

SILICON-ID-READ COMMAND

Flash memories are intended for use in applications where

the local CPU alters memory contents. As such, manu-

facturer and device codes must be accessible while the

device resides in the target system. PROM program-

mers typically access signature codes by raising A9 to

a high voltage. However, multiplexing high voltage onto

address lines is not generally desired system design prac-

tice.

The MX29F001T/B contains a Silicon-ID-Read operation

to supplement traditional PROM programming method-

ology. The operation is initiated by writing the read sili-

con ID command sequence into the command register.

Following the command write, a read cycle with

A1=VIL,A0=VIL retrieves the manufacturer code of C2H.

A read cycle with A1=VIL, A0=VIH returns the device

code of 18H for MX29F001T,19H for MX29F001B.

SET-UP AUTOMATIC CHIP ERASE COM-

MANDS

Chip erase is a six-bus cycle operation. There are two

"unlock" write cycles. These are followed by writing the

"set-up" command 80H. Two more "unlock" write cycles

are then followed by the chip erase command 10H.

The Automatic Chip Erase does not require the device

to be entirely pre-programmed prior to executing the Au-

tomatic Chip Erase. Upon executing the Automatic Chip

Erase, the device will automatically program and verify

the entire memory for an all-zero data pattern. When the

device is automatically verified to contain an all-zero pat-

tern, a self-timed chip erase and verification begin. The

erase and verification operations are completed when

the data on Q7 is "1" at which time the device returns to

the Read mode. The system does not require to pro-

vide any control or timing during these operations.

When using the Automatic Chip Erase algorithm, note

that the erase automatically terminates when adequate

erase margin has been achieved for the memory array(no

erase verify command is required).

If the Erase operation was unsuccessful, the data on Q5

is "1"(see Table 4), indicating an erase operation exceed

internal timing limit.

The automatic erase begins on the rising edge of the

last WE pulse in the command sequence and terminates

when the data on Q7 is "1" and the data on Q6 stops

toggling for two consecutive read cycles, at which time

the device returns to the Read mode.

TABLE 3. EXPANDED SILICON ID CODE

Pins

A0 A1 Q7 Q6 Q5 Q4 Q3 Q2 Q1 Q0 Code (Hex)

Code

Manufacture code

VIL VIL 1 1 0 0 0 0 1 0

C2H

Device code

VIH VIL 0 0 0 1 1 0 0 0

18H

for MX29F001T

Device code

VIH VIL 0 0 0 1 1 0 0 1

19H

for MX29F001B

Chip Protection Verification X VIH 0 0 0 0 0 0 0 1 01H (Protected)

X VIH 0 0 0 0 0 0 0 0 00H (Unprotected)

P/N: PM0515

REV. 2.6, DEC. 29, 2003

7

Share Link: