HA-5137A Ver la hoja de datos (PDF) - Intersil
Número de pieza
componentes Descripción
Fabricante
HA-5137A Datasheet PDF : 9 Pages
| |||
HA-5137A
Absolute Maximum Ratings TA = 25oC
Voltage Between V+ and V- Terminals. . . . . . . . . . . . . . . . . . . . 44V
Differential Input Voltage (Note 1) . . . . . . . . . . . . . . . . . . . . . . . 0.7V
Output Current . . . . . . . . . . . . . . . . . . . . Full Short Circuit Protection
Operating Conditions
Temperature Range
HA-5137A-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 75oC
Thermal Information
Thermal Resistance (Typical, Note 2)
θJA (oC/W) θJC (oC/W)
CERDIP Package. . . . . . . . . . . . . . . . . 115
28
Maximum Junction Temperature (Hermetic Package) . . . . . . . 175oC
Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. For differential input voltages greater than 0.7V, the input current must be limited to 25mA to protect the back-to-back input diodes.
2. θJA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications VSUPPLY = ±15V, CL ≤ 50pF, RS ≤ 100Ω
PARAMETER
INPUT CHARACTERISTICS
Offset Voltage
TEST CONDITIONS
Average Offset Voltage Drift
Bias Current
Offset Current
Common Mode Range
Differential Input Resistance (Note 3)
Input Noise Voltage (Note 4)
Input Noise Voltage Density
(Note 5)
Input Noise Current Density
(Note 5)
TRANSFER CHARACTERISTICS
Large Signal Voltage Gain
Common Mode Rejection Ratio
Minimum Stable Gain
Gain-Bandwidth-Product
OUTPUT CHARACTERISTICS
Output Voltage Swing
Full Power Bandwidth (Note 6)
Output Resistance
Output Current
TRANSIENT RESPONSE (Note 7)
Rise Time
Slew Rate
Settling Time
Overshoot
POWER SUPPLY CHARACTERISTICS
Supply Current
0.1Hz to 10Hz
f = 10Hz
f = 100Hz
f = 1000Hz
f = 10Hz
f = 100Hz
f = 1000Hz
RL = 2kΩ,
VOUT = ±10V
VCM = ±10V
f = 10kHz
f = 1MHz
RL = 600Ω
RL = 2kΩ
Open Loop
VOUT = ±3V
Note 8
TEMP.
(oC)
25
Full
Full
25
Full
25
Full
Full
25
25
25
25
25
25
25
25
25
Full
Full
25
25
25
25
Full
25
25
25
25
25
25
25
25
Full
MIN
-
-
-
-
-
-
-
±10.3
1.5
-
-
-
-
-
-
-
1000
600
114
5
60
-
±10.0
±11.7
220
-
16.5
-
14
-
-
-
-
TYP
10
30
0.2
10
20
7
15
±11.5
6
0.08
3.5
3.1
3.0
1.7
1.0
0.4
1800
1200
126
-
80
63
±11.5
±13.8
320
70
25
-
20
1.0
20
3.5
-
MAX
25
60
0.6
40
60
35
50
-
-
0.18
8.0
4.5
3.8
4.0
2.3
0.6
-
-
-
-
-
-
-
-
-
-
-
100
-
-
40
-
4.0
UNITS
µV
µV
µV/oC
nA
nA
nA
nA
V
MΩ
µVP-P
nV/ Hz
nV/ Hz
nV/ Hz
pA/ Hz
pA/ Hz
pA/ Hz
V/mV
V/mV
dB
V/V
MHz
MHz
V
V
kHz
Ω
mA
ns
V/µs
µs
%
mA
mA
2
Share Link: 