RP60-2415SE Ver la hoja de datos (PDF) - RECOM Electronic GmbH
Número de pieza
componentes Descripción
Fabricante
RP60-2415SE
RECOM Electronic GmbH
RP60-2415SE Datasheet PDF : 2 Pages
| |||
POWERLINE - DC/DC-Converter
E-Series, 60 Watt, 1.6 kV Isolation & Wide Input Range (Single & Dual Output)
Specifications (typical at nominal input and 25°C unless otherwise noted)
Input Voltage Range
See „Selection Guide“ table
Input Filter
Pi Type
Reflected Ripple Current
75mA, p-p
Voltage Accuracy, Single, Dual Output Models
±2.0%, max.
Voltage Balance, Dual Output Models
±2%, max.
Ripple & Noise, 20MHz BW
1% p-p of Vout
Line Regulation:
Single Output Models
Dual Output Models
±0.5%, max.
±0.5%, max.
Load Regulation (1/10 Load Full-Load)
Minimum Output Current 800mA)
(xx3305DE) Models 3.3V
Single Output Models
Dual Output Models
±0.5%, max.
±0.5%, max.
Temperature Coefficient
±0.02%/°C
Temp. Coefficient Balance
±1.0%
Output Short Circuit Duration
Continuous
Short Circuit Protection. All outputs, by input Current limiting Output
Short Circuit Duration
Continuous
Overvoltage Protection Threshold:
3.3V Output
3.9V
5.V Output
6.2V
12V Output
15V
15V Output
18V
Control Voltage Referenced to Negative(-)Input Compatibility
CMOS, TTL
ON-Control
4.8V min. or Open
OFF-Control
0.4V max. or Short
Switching Frequency
200kHz, typ.
Isolation Voltage
1600VDC, min
Isolation Resistance
109 Ω
Operating Temperature Range
-25°C to +71°C
Storage Temperature Range
-55°C to +125°C
Cooling
Free-air Convection
EMI/RFI
Six-sided Continuos Shield
Case Material
Nickel-Coated Copper with Non-Conductive Base
Dimensions
100 x 70 x 19 mm
MTBF (MIL-HDBK-217F TA = 25°C full load)
1.250 x 105 Hours
External Output Trimming
Output may optionally be externally trimmed (± 10%)
with a fixed resistor or an external trimpot as shown.
9 7 (7)
4
6
Trim
Up
Trim
Down
9 7 (7)
RT1
or 4
RT2
6
for dual output
7 for 3.3/5.0VDC
( ) for single output
10 kΩ
Trimpot
120
100
590
LFM
80
60
40
Natural
Convection
20
Cooling
0
-25 25 50 75 100 125
35
71
Ambient Temperature °C
Package Style and Pinning (mm)
25.00
10.00
10.00
10.00
15.00
10.00
25.40
25.40
4
5
1 25.40
6
2 25.40
3
7
Bottom
View
8
9
See Note 2
10
82.60
Note: Mounting inserts: 4 - 40 x 2.5 Deep
10.00
10.00
10.00
10.00
10.00
10.00
7.60
1.3
8.0 19
70.00
Pin Connections
Pin # Single Dual
1 +Vin +Vin
2 -Vin
-Vin
3 On/Off On/Off
4 Trim Trim
5 +Vout +Vout
6 +Vout +Vout
7 Ground Ground
8 Ground Ground
9 N/P
-Vout
10 N/P
-Vout
3.3 VDC /
5.0 VDC
+Vin
-Vin
On/Off
Trim
+3.3 Vout
+3.3 Vout
Common
Common
+5.0 Vout
+5.0 Vout
Pin Pitch Tolerance ±0.5 mm
PO 72
August 2002
www.recom-international.com
Share Link: