MP2365 Ver la hoja de datos (PDF) - Monolithic Power Systems

Número de pieza

componentes Descripción

Fabricante

MP2365

3A, 28V, 1.4MHz Step-Down Converter

Monolithic Power Systems 

MP2365 – 3A, 28V, 1.4MHz STEP-DOWN CONVERTER

Output Rectifier Diode

The output rectifier diode supplies the current to

the inductor when the high-side switch is off. To

reduce losses due to the diode forward voltage

and recovery times, use a Schottky diode.

Choose a diode whose maximum reverse

voltage rating is greater than the maximum

input voltage, and whose current rating is

greater than the maximum load current. Table 2

lists example Schottky diodes and

manufacturers.

Table 2—Diode Selection Guide

Diode

Voltage/Current Manufacture

Rating

SK33

30V, 3A Diodes Inc.

SK34

40V, 3A Diodes Inc.

B330

30V, 3A Diodes Inc.

B340

40V, 3A Diodes Inc.

MBRS330

30V, 3A On Semiconductor

MBRS340

40V, 3A On Semiconductor

Input Capacitor

The input current to the step-down converter is

discontinuous, therefore a capacitor is required

to supply the AC current to the step-down

converter while maintaining the DC input

voltage. Use low ESR capacitors for the best

performance. Ceramic capacitors are preferred,

but tantalum or low-ESR electrolytic capacitors

may also suffice.

Since the input capacitor (C1) absorbs the input

switching current it requires an adequate ripple

current rating. The RMS current in the input

capacitor can be estimated by:

IC1 = ILOAD ×

VOUT

VIN

×⎜⎜⎛1−

⎝

VOUT

VIN

⎟⎞

⎟

⎠

The worst-case condition occurs at VIN = 2VOUT,

where:

IC1

=

ILOAD

2

For simplification, choose the input capacitor

whose RMS current rating greater than half of

the maximum load current.

The input capacitor can be electrolytic, tantalum

or ceramic. When using electrolytic or tantalum

capacitors, a small, high quality ceramic

capacitor, i.e. 0.1µF, should be placed as close

to the IC as possible. When using ceramic

capacitors, make sure that they have enough

capacitance to provide sufficient charge to

prevent excessive voltage ripple at input. The

input voltage ripple caused by capacitance can

be estimated by:

∆VIN

=

ILOAD ×

fS × C1

VOUT

VIN

× ⎜⎜⎝⎛1 −

VOUT

VIN

⎟⎟⎠⎞

Output Capacitor

The output capacitor (C2) is required to

maintain the DC output voltage. Ceramic,

tantalum, or low ESR electrolytic capacitors are

recommended. Low ESR capacitors are

preferred to keep the output voltage ripple low.

The output voltage ripple can be estimated by:

∆VOUT

=

VOUT

fS × L

× ⎜⎜⎝⎛1−

VOUT

VIN

⎟⎟⎠⎞ × ⎜⎜⎝⎛RESR

+

8

×

f

1

S×

C2

⎟⎟⎠⎞

Where L is the inductor value and RESR is the

equivalent series resistance (ESR) value of the

output capacitor.

In the case of ceramic capacitors, the

impedance at the switching frequency is

dominated by the capacitance. The output

voltage ripple is mainly caused by the

capacitance. For simplification, the output

voltage ripple can be estimated by:

∆VOUT

=

8

×

VOUT

fS2 × L ×

C2

×

⎜⎜⎝⎛1 −

VOUT

VIN

⎟⎟⎠⎞

In the case of tantalum or electrolytic

capacitors, the ESR dominates the impedance

at the switching frequency. For simplification,

the output ripple can be approximated to:

∆VOUT

=

VOUT

fS × L

×

⎜⎜⎝⎛1 −

VOUT

VIN

⎟⎟⎠⎞ × RESR

The characteristics of the output capacitor also

affect the stability of the regulation system. The

MP2365 can be optimized for a wide range of

capacitance and ESR values.

MP2365 Rev. 0.91

www.MonolithicPower.com

7

7/10/2006

MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.

© 2006 MPS. All Rights Reserved.

Share Link: