MCM6209CJ25 Ver la hoja de datos (PDF) - Motorola => Freescale
Número de pieza
componentes Descripción
Fabricante
MCM6209CJ25 Datasheet PDF : 8 Pages
| |||
CAPACITANCE (f = 1 MHz, dV = 3 V, TA = 25°C, Periodically Sampled Rather Than 100% Tested)
Characteristic
Address Input Capacitance
Control Pin Input Capacitance (E, G, W)
I/O Capacitance
Symbol
Cin
Cin
CI/O
Max
Unit
6
pF
6
pF
8
pF
AC OPERATING CONDITIONS AND CHARACTERISTICS
(VCC = 5.0 V ± 10%, TA = 0 to + 70°C, Unless Otherwise Noted)
Input Timing Measurement Reference Level . . . . . . . . . . . . . . . 1.5 V
Input Pulse Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 3.0 V
Input Rise/Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 ns
Output Timing Measurement Reference Level . . . . . . . . . . . . . 1.5 V
Output Load . . . . . . . . . . . . . . . . Figure 1A Unless Otherwise Noted
READ CYCLE (See Notes 1 and 2)
– 12
– 15
– 20
– 25
– 35
Parameter
Symbol Min Max Min Max Min Max Min Max Min Max Unit Notes
Read Cycle Time
tAVAV 12 — 15 — 20 — 25 — 35 —
ns
2
Address Access Time
tAVQV — 12 — 15 — 20 — 25 — 35 ns
Enable Access Time
tELQV — 12 — 15 — 20 — 25 — 35 ns
3
Output Enable Access Time
tGLQV — 6 — 8 — 10 — 12 — 15 ns
Output Hold from Address Change
tAXQX 4
—
4
—
4
—
4
—
4
—
ns
Enable Low to Output Active
tELQX 4
—
4
—
4
—
4
—
4
—
ns 4, 5, 6
Enable High to Output High–Z
tEHQZ 0
6
0
8
0
9
0 10 0 10
ns 4, 5, 6
Output Enable Low to Output Active
tGLQX 0
—
0
—
0
—
0
—
0
—
ns 4, 5, 6
Output Enable High to Output High–Z tGHQZ 0
6
0
7
0
8
0 10 0 —
ns 4, 5, 6
Power Up Time
tELICCH 0
—
0
—
0
—
0
—
0
—
ns
Power Down Time
tEHICCL — 12 — 15 — 20 — 25 — 35 ns
NOTES:
1. W is high for read cycle.
2. All timings are referenced from the last valid address to the first transitioning address.
3. Addresses valid prior to or coincident with E going low.
4. At any given voltage and temperature, tEHQZ max is less than tELQX min, and tGHQZ max is less than tGLQX min, both for a given device
and from device to device.
5. Transition is measured ± 500 mV from steady–state voltage with load of Figure 1B.
6. This parameter is sampled and not 100% tested.
7. Device is continuously selected (E = VIL, G ≤ VIL).
OUTPUT
AC TEST LOADS
Z0 = 50 Ω
RL = 50 Ω
VL = 1.5 V
OUTPUT
255 Ω
+5V
480 Ω
5 pF
Figure 1A
Figure 1B
TIMING LIMITS
The table of timing values shows either a
minimum or a maximum limit for each param-
eter. Input requirements are specified from
the external system point of view. Thus, ad-
dress setup time is shown as a minimum
since the system must supply at least that
much time (even though most devices do not
require it). On the other hand, responses from
the memory are specified from the device
point of view. Thus, the access time is shown
as a maximum since the device never pro-
vides data later than that time.
MOTOROLA FAST SRAM
MCM6209C
3
Share Link: 