MCM6209CJ25 Ver la hoja de datos (PDF) - Motorola => Freescale
Número de pieza
componentes Descripción
Fabricante
MCM6209CJ25 Datasheet PDF : 8 Pages
| |||
TRUTH TABLE (X = Don’t Care)
E
G
W
Mode
H
X
X
Not Selected
L
H
H Output Disabled
L
L
H
Read
L
X
L
Write
VCC Current
ISB1, ISB2
ICCA
ICCA
ICCA
Output
High–Z
High–Z
Dout
High–Z
Cycle
—
—
Read
Write
ABSOLUTE MAXIMUM RATINGS (See Note)
Rating
Symbol
Value
Unit
Power Supply Voltage
VCC
– 0.5 to + 7.0
V
Voltage Relative to VSS For Any Pin
Except VCC
Vin, Vout – 0.5 to VCC + 0.5 V
Output Current
Iout
± 20
mA
Power Dissipation
PD
1.0
W
Temperature Under Bias
Tbias
– 10 to + 85
°C
Operating Temperature
TA
0 to + 70
°C
Storage Temperature — Plastic
Tstg
– 55 to + 125
°C
NOTE: Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are
exceeded. Functional operation should be restricted to RECOMMENDED OPER-
ATING CONDITIONS. Exposure to higher than recommended voltages for
extended periods of time could affect device reliability.
This device contains circuitry to protect the
inputs against damage due to high static volt-
ages or electric fields; however, it is advised
that normal precautions be taken to avoid
application of any voltage higher than maxi-
mum rated voltages to this high–impedance
circuit.
This CMOS memory circuit has been
designed to meet the dc and ac specifications
shown in the tables, after thermal equilibrium
has been established. The circuit is in a test
socket or mounted on a printed circuit board
and transverse air flow of at least 500 linear
feet per minute is maintained.
DC OPERATING CONDITIONS AND CHARACTERISTICS
(VCC = 5.0 V ± 10%, TA = 0 to 70°C, Unless Otherwise Noted)
RECOMMENDED OPERATING CONDITIONS
Parameter
Symbol
Supply Voltage (Operating Voltage Range)
Input High Voltage
VCC
VIH
Input Low Voltage
VIL
* VIL (min) = – 0.5 V dc; VIL (min) = – 2.0 V ac (pulse width ≤ 20 ns)
** VIH (max) = VCC + 0.3 V dc; VIH (max) = VCC + 2.0 V ac (pulse width ≤ 20 ns)
Min
4.5
2.2
– 0.5*
Typ
Max
Unit
5.0
5.5
V
—
VCC + 0.3** V
—
0.8
V
DC CHARACTERISTICS
Parameter
Symbol
Min
Max
Unit
Input Leakage Current (All Inputs, Vin = 0 to VCC)
Output Leakage Current (E = VIH or G = VIH, Vout = 0 to VCC)
Standby Current (E ≥ VCC – 0.2 V*, Vin ≤ VSS + 0.2 V, or ≥ VCC – 0.2 V,
VCC = Max, f = 0 MHz)
Ilkg(I)
—
Ilkg(O)
—
ISB2
—
±1
µA
±1
µA
20
mA
Output Low Voltage (IOL = 8.0 mA)
VOL
—
0.4
V
Output High Voltage (IOH = – 4.0 mA)
VOH
2.4
—
V
*For devices with multiple chip enables, E1 and E2 are represented by E in this data sheet. E2 is of opposite polarity to E.
POWER SUPPLY CURRENTS
Parameter
AC Supply Current (Iout = 0 mA, VCC = Max, f = fmax)
Standby Current (E = VIH , VCC = Max, f = fmax)
Symbol
– 12
– 15
– 20
– 25
– 35 Unit
ICCA
ISB1
165
155
145
135
130
mA
55
50
45
40
35
mA
MCM6209C
2
MOTOROLA FAST SRAM
Share Link: 