MC100EP116FA Ver la hoja de datos (PDF) - ON Semiconductor
Número de pieza
componentes Descripción
Fabricante
MC100EP116FA Datasheet PDF : 11 Pages
| |||
MC10EP116, MC100EP116
Table 3. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Condition 2
Rating
Units
VCC
PECL Mode Power Supply
VEE
NECL Mode Power Supply
VI
PECL Mode Input Voltage
NECL Mode Input Voltage
Iout
Output Current
VEE = 0 V
VCC = 0 V
VEE = 0 V
VCC = 0 V
Continuous
Surge
VI ≤ VCC
VI ≥ VEE
6
V
−6
V
6
V
−6
50
mA
100
IBB
VBB Sink/Source
TA
Operating Temperature Range
Tstg
Storage Temperature Range
qJA
Thermal Resistance (Junction−to−Ambient) 0 lfpm
500 lfpm
32 LQFP
32 LQFP
± 0.5
−40 to +85
−65 to +150
80
55
mA
°C
°C
°C/W
qJC
Thermal Resistance (Junction−to−Case)
Standard Board
32 LQFP
qJA
Thermal Resistance (Junction−to−Ambient) 0 lfpm
500 lfpm
32 QFN
32 QFN
12 to 17
31
27
°C/W
°C/W
qJC
Thermal Resistance (Junction−to−Case)
2S2P
Tsol
Wave Solder
Pb
Pb−Free
32 QFN
12
°C/W
265
°C
265
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 4. 10EP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 2)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
VOH
VOL
VIH
VIL
VBB
VIHCMR
Power Supply Current
Output HIGH Voltage (Note 3)
Output LOW Voltage (Note 3)
Input HIGH Voltage (Single−Ended)
Input LOW Voltage (Single−Ended)
Output Voltage Reference
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 4)
60
75
90
60
80
95
60
85
95 mA
2165 2290 2415 2230 2355 2480 2290 2415 2540 mV
1365 1490 1615 1430 1555 1680 1490 1615 1740 mV
2090
2415 2155
2480 2215
2540 mV
1365
1690 1460
1755 1490
1815 mV
1790 1890 1990 1855 1955 2055 1915 2015 2115 mV
2.0
3.3 2.0
3.3 2.0
3.3
V
IIH
Input HIGH Current
IIL
Input LOW Current
150
150
150 mA
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
2. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to −2.2 V.
3. All loading with 50 W to VCC − 2.0 V.
4. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
http://onsemi.com
4
Share Link: 