MC100ELT22(2000) Ver la hoja de datos (PDF) - ON Semiconductor
Número de pieza
componentes Descripción
Fabricante
MC100ELT22 Datasheet PDF : 8 Pages
| |||
MC10ELT22, MC100ELT22
MAXIMUM RATINGS (Note 1.)
Symbol
Parameter
Condition 1
VCC
Positive Power Supply
VIN
Input Voltage
Iout
Output Current
GND = 0 V
GND = 0 V
Continuous
Surge
TA
Operating Temperature Range
Tstg
Storage Temperature Range
θJA
Thermal Resistance (Junction to Ambient)
0 LFPM
500 LFPM
θJC
Thermal Resistance (Junction to Case)
std bd
θJA
Thermal Resistance (Junction to Ambient)
0 LFPM
500 LFPM
θJC
Thermal Resistance (Junction to Case)
std bd
Tsol
Wave Solder
<2 to 3 sec @ 248°C
1. Maximum Ratings are those values beyond which device damage may occur.
Condition 2
VI VCC
8 SOIC
8 SOIC
8 SOIC
8 TSSOP
8 TSSOP
8 TSSOP
Rating
7
7
50
100
–40 to +85
–65 to +150
190
130
41 to 44
185
140
41 to 44 ± 5%
265
Units
V
V
mA
mA
°C
°C
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C
10ELT SERIES PECL DC CHARACTERISTICS VCC = 5.0 V; GND = 0.0 V (Note 1.)
–40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
ICC
Power Supply Current
22
22
22 mA
VOH
Output HIGH Voltage (Note 2.)
3920 4010 4110 4020 4105 4190 4090 4185 4280 mV
VOL
Output LOW Voltage (Note 2.)
3050 3200 3350 3050 3210 3370 3050 3227 3405 mV
NOTE: Devices are designed to meet the DC specifications shown in the above table, after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained.
1. Output parameters vary 1:1 with VCC. VCC can vary ± 0.25 V.
2. Outputs are terminated through a 50 ohm resistor to VCC–2 volts.
100ELT SERIES PECL DC CHARACTERISTICS VCC = 5.0 V; GND = 0.0 V (Note 1.)
–40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
ICC
Power Supply Current
22
22
22 mA
VOH
Output HIGH Voltage (Note 2.)
3915 3995 4120 3975 4045 4120 3975 4050 4120 mV
VOL
Output LOW Voltage (Note 2.)
3170 3305 3445 3190 3295 3380 3190 3295 3380 mV
NOTE: Devices are designed to meet the DC specifications shown in the above table, after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained.
1. Output parameters vary 1:1 with VCC. VCC can vary ± 0.25 V.
2. Outputs are terminated through a 50 ohm resistor to VCC–2 volts.
http://onsemi.com
2
Share Link: 