MAX4719EBC Ver la hoja de datos (PDF) - Maxim Integrated
Número de pieza
componentes Descripción
Fabricante
MAX4719EBC Datasheet PDF : 11 Pages
| |||
20Ω, 300MHz Bandwidth, Dual SPDT Analog
Switch in UCSP
ABSOLUTE MAXIMUM RATINGS
(All Voltages Referenced to GND)
V+, IN_...................................................................-0.3V to +6.0V
COM_, NO_, NC_ (Note 1) ...........................-0.3V to (V+ + 0.3V)
Continuous Current COM_, NO_, NC_ ...........................±100mA
Peak Current COM_, NO_, NC_
(pulsed at 1ms, 10% duty cycle)................................±200mA
Continuous Power Dissipation (TA = +70°C)
10-Pin µMAX (derate 5.6mW/°C above +70°C) ...........444mW
12-Bump UCSP (derate 11.4mW/°C above +70°C) ....909mW
ESD Method 3015.7 ...............................................................2kV
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Bump Temperature (soldering) (Note 2)
Infrared (15s) ...............................................................+220°C
Vapor Phase (60s) .......................................................+215°C
Note 1: Signals on COM_, NO_, or NC_ exceeding V+ or GND are clamped by internal diodes. Limit forward-diode current to maxi-
mum current rating.
Note 2: This device is constructed using a unique set of packaging techniques that impose a limit on the thermal profile the device
can be exposed to during board level solder attach and rework. This limit permits only the use of the solder profiles recom-
mended in the industry standard specification, JEDEC 020A, paragraph 7.6, table 3 for IR/VPR and convection reflow.
Preheating is required. Hand or wave soldering is not allowed.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—Single +3V Supply
(V+ = +2.7V to +3.6V, VIH = +1.4V, VIL = +0.5V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at V+ = +3.0V,
TA = +25°C, unless otherwise noted.) (Notes 3, 4)
PARAMETER
SYMBOL
CONDITIONS
TA
MIN TYP MAX UNITS
Analog Signal Range
VCOM_,
VNO_, VNC_
TMIN to
0
TMAX
V+
V
ANALOG SWITCH
On-Resistance (Note 5)
RON
V+ = 2.7V, ICOM_ = 10mA;
VNO_ or VNC_ = 1.5V
+25°C
TMIN to
TMAX
14
20
Ω
25
On-Resistance Match Between
Channels (Notes 5, 6)
∆RON
V+ = 2.7V, ICOM_ = 10mA;
VNO_ or VNC_ = 1.5V
+25°C
TMIN to
TMAX
0.15 0.4
Ω
0.5
On-Resistance Flatness
(Note 7)
RFLAT(ON)
V+ = 2.7V, ICOM_ = 10mA;
VNO_ or VNC_ = 1.0V, 1.5V, 2.0V
+25°C
TMIN to
TMAX
0.6
1.2
Ω
1.5
+25°C -0.5 0.01 +0.5
NO_, NC_ Off-Leakage Current
(Note 8)
INO_(OFF), V+ = 3.6V, VCOM_ = 0.3V, 3.3V;
INC_(OFF) VNO_ or VNC_ = 3.3V, 0.3V
TMIN to
TMAX
-1
nA
+1
COM_ On-Leakage Current
(Note 8)
V+ = 3.6V, VCOM_ = 0.3V, 3.3V; +25°C
-1
0.01
+1
ICOM_(ON) VNO_ or VNC_ = 0.3V, 3.3V, or
floating
TMIN to
TMAX
-2
nA
+2
DYNAMIC CHARACTERISTICS
Turn-On Time
+25°C
tON
VNO_, VNC_ = 1.5V;
RL = 300Ω, CL = 35pF, Figure 1
TMIN to
TMAX
40
80
ns
100
2 _______________________________________________________________________________________
Share Link: 