DatasheetQ Logo
Electronic component search and free download site. Transistors,MosFET ,Diode,Integrated circuits

MAX4734(2002) Ver la hoja de datos (PDF) - Maxim Integrated

Número de pieza
componentes Descripción
Fabricante
MAX4734
(Rev.:2002)
MaximIC
Maxim Integrated MaximIC
MAX4734 Datasheet PDF : 11 Pages
1 2 3 4 5 6 7 8 9 10
0.8, Low-Voltage, 4-Channel
Analog Multiplexer
ELECTRICAL CHARACTERISTICSSingle 1.8V Supply
(V+ = 1.8V, VIH = 1.0V, VIL = 0.4V, TA = TMIN to TMAX, unless otherwise specified. Typical values are at TA = +25°C.) (Notes 2, 3)
PARAMETER
ANALOG SWITCH
Analog Signal Range
SYMBOL
VCOM,
VNO_
On-Resistance
RON
SWITCH DYNAMIC CHARACTERISTICS
Turn-On Time
tON
CONDITIONS
ICOM_ = 10mA,
VNO_ = 1V
VNO_ = 1V,
RL = 50Ω, CL = 35pF,
Figure 1
TA
MIN TYP MAX UNITS
0
V+
V
+25°C
TMIN to TMAX
1.5
2
3
+25°C
TMIN to TMAX
25
30
ns
35
Turn-Off Time
VNO_ = 1V,
tOFF
RL = 50Ω, CL = 35pF,
Figure 1
+25°C
TMIN to TMAX
18
25
ns
28
VNO_ = 1V,
+25°C
7
Break-Before-Make (Note 8)
tBBM
RL = 50Ω, CL = 35pF,
ns
Figure 2
TMIN to TMAX
1
Charge Injection
Q
VGEN = 0, RGEN = 0,
CL = 1nF, Figure 3
+25°C
35
pC
Off-Isolation (Note 9)
VISO
f = 1MHz, VNO_
= 1VP-P, RL = 50,
CL = 5pF, Figure 5
+25°C
-56
dB
Crosstalk (Note 10)
LOGIC INPUT (A_, EN)
Input Logic High
Input Logic Low
Input Leakage Current
f = 1MHz, VCOM = 1VP-P,
VCT
RL = 50,
+25°C
CL = 5pF, Figure 5
VIH
VIL
IIN
VEN = 0 or 3.6V,
VA_ = 0 or 3.6V
-56
dB
1
V
0.4
V
1
µA
Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value is a maximum, is
used in this data sheet.
Note 3: -40°C specifications are guaranteed by design.
Note 4: RON and RON matching specifications for QFN packaged parts are guaranteed by design.
Note 5: RON = RON(MAX) - RON(MIN).
Note 6: Flatness is defined as the difference between the maximum and the minimum value of on-resistance as measured over
the specified analog signal ranges.
Note 7: Leakage parameters are 100% tested at hot temperature and guaranteed by correlation at room temperature.
Note 8: Guaranteed by design.
Note 9: Off-Isolation = 20log10(VCOM/VNO_), VCOM = output, VNO_ = input to off switch.
Note 10: Between two switches.
4 _______________________________________________________________________________________

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]