MASW-009482-001SMB Ver la hoja de datos (PDF) - M/A-COM Technology Solutions, Inc.

Número de pieza

componentes Descripción

Fabricante

MASW-009482-001SMB

GaAs Broadband High Power SP3T Switch DC - 4.0 GHz

M/A-COM Technology Solutions, Inc. 

MASW-009482

GaAs Broadband High Power SP3T Switch

DC - 4.0 GHz

Rev. V1

Applications Section: Tri-Mode Mobile Phone Performance

Typical Electrical Performance: TA = 25°C, Z0 = 50Ω, VC = 0V/2.6V, 1000pF Capacitors 1

Parameter

Test Conditions

Units Min. Typ. Max.

Insertion Loss

(All Paths)

824 - 894 MHz (CELL)

1710 - 1755 MHz (AWS)

1850 - 1990 MHz (PCS)

dB

—

0.55

—

dB

—

0.65

—

dB

—

0.75

—

Isolation

824 - 894 MHz (CELL)

1710 - 1755 MHz (AWS)

1850 - 1990 MHz (PCS)

dB

—

27

—

dB

—

23

—

dB

—

22

—

Return Loss

(All RF ports)

DC - 2.5 GHz

dB

—

20

—

Input IP3

Two Tone, +23 dBm/tone, 1 MHz Spacing, 894 MHz

Two Tone, +23 dBm/tone, 1 MHz Spacing, 1755 MHz

Two Tone, +23 dBm/tone, 1 MHz Spacing, 1990 MHz

dBm

dBm

dBm

—

—

68

65

67

—

—

For Cell Band: Two-tone signal input:

TX1 = +22 dBm @ 820 MHz, TX2 = +22 dBm @ 821 MHz, dBm

—

-105

—

RX interferer = -23 dBm @ 865 MHz2

Cross Modulation

For PCS Band: Two-tone signal input:

TX1 = +18 dBm @ 1880 MHz, TX2 = +18 dBm @ 1881 MHz, dBm —

-103

—

RX interferer = -23 dBm @ 1960 MHz2

2nd Harmonic

Fin = 894 MHz, Pin = +25.5 dBm

Fin = 1755 MHz, Pin = +25.0 dBm

Fin = 1990 MHz, Pin = +24.0 dBm

dBc

dBc

dBc

—

—

81

81

85

—

—

3rd Harmonic

Fin = 894 MHz, Pin = +25.5 dBm

Fin = 1755 MHz, Pin = +25.0 dBm

Fin = 1990 MHz, Pin = +24.0 dBm

dBc

dBc

dBc

—

—

82

81

91

—

—

Input P0.1dB

Fin = 894 MHz

Fin = 1755 MHz

Fin = 1990 MHz

dBm

34.5

dBm —

36.0

—

dBm

35.5

Trise, Tfall

10% to 90% RF, 90% to 10% RF, 900 MHz

ns

—

45

—

Ton, Toff

50% control to 90% RF, and 50% control to 10% RF,

900 MHz

ns

—

70

—

Transients

In Band

mV

—

40

—

Control Current

VC = 0 V/2.6 V

µA

—

6

—

1. External DC blocking capacitors are required on all RF ports. Typical performance specifications are with 1000 pF blocking and decoupling

capacitors / as shown on the application schematic .

2. RX Interferer power set to –10 dBm during test to improve dynamic range of measurement system. Typical performance with –23 dBm

interferer is determined by using a linear relationship between interferer power level and cross modulation products.

6

M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.

Visit www.macom.com for additional data sheets and product information.

For further information and support please visit:

https://www.macom.com/support

Share Link: