MASW-007075-000100 Ver la hoja de datos (PDF) - M/A-COM Technology Solutions, Inc.
Número de pieza
componentes Descripción
Fabricante
MASW-007075-000100
M/A-COM Technology Solutions, Inc.
MASW-007075-000100 Datasheet PDF : 5 Pages
| |||
MASW-007075
GaAs SPDT Absorptive Switch with
ASIC Driver, DC-3.0 GHz
Rev. V4
Electrical Specifications: TA = 25°C, Z0 = 50
Parameter
Test Conditions
Units
Min
Typ
Max
Insertion Loss
Isolation
(All arms off)
VSWR
Trise Tfall
Ton
Toff
Transients
1 dB Compression
Input IP3
VCC
VEE
VIL
VIH
lin (Input Leakage Current)
Icc
(Quiescent Supply Current)
ΔIcc
(Additional Supply Current Per
TTL Input Pin)
IEE
DC - 3.0 GHz
DC - 3.0 GHz
DC - 3.0 GHz
On
Off
10%/90%, 90%/10% 1
50% TTL to 90%/10% RF
In-band (peak to peak)
.05 GHz
.5 - 3.0 GHz
Two tone inputs 0.05 GHz
up to +5 dBm 0.5 - 3.0 GHz
—
—
LOW-level input voltage
HIGH-level input voltage
Vin = VCC or GND
Vcntrl = VCC or GND
VCC = Max, Vcntrl = VCC - 2.1 V
VEE min to max, Vin = VIL or VIH
dB
dB
—
—
ns
ns
mV
dBm
dBm
dBm
dBm
V
V
V
V
uA
uA
mA
mA
—
33
—
—
—-
—
—
—
—
—
—
+4.5
-8.0
0.0
2.0
-1.0
—
—
-1.0
1.8
36
1.7:1
2.1:1
15
50
50
+20
+27
+35
+46
+5.0
-5.0
—
—
—
250
—
-0.2
2.2
—
2.2:1
2.2:1
50
150
150
—
—
—
—
+5.5
-4.75
0.8
5.0
1.0
400
1.0
—
1. Decoupling capacitors (.01 µF) are required on the power supply lines.
Absolute Maximum Ratings 2,3
Parameter
Absolute Maximum
Handling Procedures
Please observe the following precautions to avoid
damage:
Max. Input Power
0.05 GHz
0.5 - 3.0 GHz4
VCC
VEE
VCC - VEE
Vin5
Operating Temperature
Storage Temperature
+27 dBm
+34 dBm
-0.5V ≤ VCC ≤ +7.0V
-8.5V ≤ VEE ≤ +0.5V
-0.5V ≤ VCC - VEE ≤ 14.5V
-0.5V ≤ Vin ≤ VCC + 0.5V
-40ºC to +85ºC
-65ºC to +125ºC
Static Sensitivity
Gallium Arsenide Integrated Circuits are sensitive
to electrostatic discharge (ESD) and can be
damaged by static electricity. Proper ESD control
techniques should be used when handling these
devices.
Truth Table
2. Exceeding any one or combination of these limits may cause
permanent damage to this device.
3. M/A-COM does not recommend sustained operation near
these survivability limits.
4. When the RF input is applied to the terminated port, the
absolute maximum power is +30 dBm.
2
5. Standard CMOS TTL interface, latch-up will occur if logic
signal is applied prior to power supply.
TTL Control Input
C1
C2
1
0
0
1
RF Common To:
RF1
RF2
On
Off
Off
On
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
Share Link: