HLMP-D120 Ver la hoja de datos (PDF) - HP => Agilent Technologies

Número de pieza

componentes Descripción

Fabricante

HLMP-D120

T-13/4 (5 mm), T-1 (3 mm), High Performance, Tinted, Diffused, AlInGaP, and TS AlGaAs Red LED Lamps

HP => Agilent Technologies 

capable of producing high light

output over the wide range of

drive currents from 500 µA to

50 mA. The color is deep red at a

dominant wavelength of 644 nm.

TS AlGaAs is a flip-chip LED

technology, die attached to the

anode lead and wire bonded to

the cathode lead. Available view-

ing angles are 25°, 40°, and 55°.

Package Dimensions

5.08 (0.200)

4.57 (0.180)

9.19 (0.362)

8.43 (0.332)

0.89 (0.035)

0.64 (0.025)

6.35 (0.250)

5.58 (0.220)

CATHODE

25.40 MIN.

(1.00)

24.13

(0.95)

MIN.

3.18 (0.125)

2.67 (0.105)

3.43 (0.135)

2.92 (0.115)

4.70 (0.185)

4.19 (0.165)

1.02

(0.040) NOM.

0.45 SQUARE NOMINAL

(0.018)

6.35 (0.250)

5.58 (0.220)

3.18 (0.125)

2.67 (0.105)

3.43 (0.135)

2.92 (0.115)

4.70 (0.185)

4.19 (0.165)

1.02

(0.040) NOM.

0.45

(0.018)

SQUARE

NOMINAL

2(04..9153) MIN.

1.27( 0.050) NOM.

1.27

(0.050)

NOM.

0.45 (0.018)

SQUARE

NOMIMAL

6.10 (0.240)

5.59 (0.220)

CATHODE

2.54 (0.100) NOM.

A

NOTES:

1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).

2. AN EPOXY MENISCUS MAY EXTEND ABOUT

1 mm (0.040") DOWN THE LEADS.

CATHODE

ANODE

(02..15040)NOM.

B

ANODE

CATHODE

2.54 NOM.

(0.100)

1.27

(0.050)

NOM.

C

HLMA-DL05/DH05/Kl05/KH05 AlInGaP Lamps

Absolute Maximum Ratings at TA = 25°C

Parameter

DC Forward Current[1,3,4]

HLMA-

DL05

50

HLMA-

DH05

50

HLMA-

KL05

50

HLMA-

KH05

50

Peak Forward Current[2]

200

200

200

200

Average Input Power[2]

103

103

103

103

Reverse Voltage (IR = 100 µA)

Operating Temperature Range

5

-40 to

+100

5

-40 to

+100

5

-40 to

+100

5

-40 to

+100

Storage Temperature Range

-55 to

+100

-55 to

+100

-55 to

+100

-55 to

+100

Junction Temperature

110

Soldering Temperature

[1.59 mm (0.06 in.) below seating plane]

260°C for 5 second

Notes:

1. Derate linearly as shown in Figure 4.

2. Any pulsed operation cannot exceed the Absolute Max Peak Forward current as specified in Figure 5.

3. Drive currents between 10 mA and 30 mA are recommended for best long term performance.

4. Operation at currents below 10 mA is not recommended, please contact your Hewlett-Packard sales representative.

1-50

Units

mA

mA

mW

V

°C

°C

°C

Share Link: