LB1881V Ver la hoja de datos (PDF) - SANYO -> Panasonic
Número de pieza
componentes Descripción
Fabricante
LB1881V Datasheet PDF : 7 Pages
| |||
LB1881V
Allowable Operating Ranges at Ta = 25°C
Parameter
Supply voltage
Symbol
VCC1
VCC2
VS
Conditions
VCC1 ≤ VCC2
Ratings
Unit
4.0 to 6.0
V
4 to 10
V
Up to VCC2
V
Electrical Characteristics at Ta = 25°C, VCC1 = 5 V, VCC2 = 7 V, VS = 3 V
Parameter
Supply current
Output quiescent current
Output saturation voltage
Output TRS withstand voltage
Output quiescent voltage
Hall amplifier input offset voltage
Hall amplifier common mode input
voltage range
Hall I/O voltage gain
Brake pin high level voltage
Brake pin low level voltage
Brake pin input current
Brake pin leakage current
FRC pin high level voltage
FRC pin low level voltage
FRC pin input current
FRC pin leakage current
Upper side residual voltage
Lower side residual voltage
Residual voltage inflection point
Overlap level
Overlap vertical difference
Standby on voltage
Standby off voltage
Standby pin bias current
Thermal protection circuit operating
temperature
Thermal protection circuit hysteresis
FG amplifier input offset voltage
Open loop voltage gain
Source output saturation voltage
Sink output saturation voltage
Common mode signal exclusion ratio
FG amplifier common mode input
voltage range
Phase margin
Schmitt amplifier threshold voltage
Schmitt amplifier hysteresis width
Symbol
Conditions
ICC1
ICC2
IS
ICCOQ
ISOQ
VO(sat)
VO(sus)
VOQ
VHOFFSET
VBR = 5 V
VBR = 5 V
VBR = 5 V, RL = ∞
VSTBY = 0 V
VSTBY = 0 V, RL = ∞
IOUT = 0.6 A, sink + source
IOUT = 20 mA*1
VBR = 5 V
*1
VHCOM
GVHO
VBRH
VBRL
IBRIN
IBRLEAK
VFRCH
VFRCL
IFRCIN
IFRCLEAK
VXH
VXL
VS∆VX
OL
∆OL
VSTBYL
VSTBYH
ISTBYIN
Rangle = 8.2 kΩ
IOUT = 100 mA, VCC2 = 6 V, VS = 2 V
IOUT = 100 mA, VCC2 = 6 V, VS = 2 V
IOUT = 100 mA, VCC2 = 6 V*1
VCC2 = 6 V, VS = 3 V, RL = 100 Ω (Y)
VCC2 = 6 V, VS = 3 V, RL = 100 Ω (Y)
*2
TTSD
∆TTSD
VFG OFFSET
GVFG
VFG OU
VFG OD
GHR
*1
*1
f = 10 kHz
IO = –2 mA
IO = 2 mA
*1
VFG CH
φM
VFGS SH
VFGS HIS
*1
VFGIN+ = 2.5 V,
when VFGOUT2 goes from high to low
VFGIN+ = 2.5 V
Ratings
min
typ
3.0
6.5
12
1.45
1.55
–5
Unit
max
5.0 mA
10.0 mA
5.0 mA
100 µA
150 µA
1.7 V
V
1.65 V
+5 mV
1.4
34.0
37.0
2.0
2.8
0.285
0.350
0.9
60
70
–10
0
–0.2
2
2.8 V
40.0 dB
V
0.8 V
120 µA
–30 µA
V
1.2 V
100 µA
–30 µA
0.455 V
0.440 V
V
80 %
+10 %
+0.8 V
5V
100 µA
150
180
15
–8
43
3.7
80
210 °C
°C
+8 mV
dB
V
1.3 V
dB
0
20
3.5 V
deg
2.45
2.50
20
40
2.55 V
60 mV
Note: 1. These are target settings, and are not measured. The overlap ratings are taken as test ratings without change.
2. When the standby pin is open the IC will be in the standby state.
No. 4456-2/7
Share Link: 