HIP9022 Ver la hoja de datos (PDF) - Intersil
Número de pieza
componentes Descripción
Fabricante
HIP9022 Datasheet PDF : 10 Pages
| |||
HIP9022
Absolute Maximum Ratings
Thermal Information
Maximum Analog Supply Voltage, VDD . . . . . . . . . . . -0.3V to 14V
Logic Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6V
Analog Negative Supply Voltage, VEE . . . . . . . . . . . . . 0.3V to -5.5
Maximum Laser Protection Diode Current . . . . . . . . . . 10A, 200ns
Operating Conditions
Thermal Resistance (Typical, Note 1)
θJC (oC/W)
PLCC Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40
Maximum Operating Junction Temperature, TJ . . . . . . . . . . . 100oC
Maximum
Maximum
Storage Temperature Range,
Lead Temperature (Soldering
TSTG
10s) .
.
.
.
.
.
.
.
.
-55oC to
.......
150oC
300oC
VDD Supply Voltage Range, VDD . . . . . . . . . . . . . . 11.4V to 12.6V
VCC Supply Voltage Range, VCC . . . . . . . . . . . . . . . . 4.5V to 5.5V
VEE Supply Voltage Range, VEE . . . . . . . . . . . . . . . . -4.5V to -5.5V
Laser Power Supply Range, VLAS . . . . . . . . . . . . . . . . . . 3V to 5V
TEC Power Supply Range, VTEC . . . . . . . . . . . . . . . . . . . 3V to 5V
Laser Operating Current Range, IDL . . . . . . . . . . . . . . . . . 0A to 2A
TEC Operating Current Range, ITEC . . . . . . . . . . . . . . . . . 0A to 2A
Die Characteristics
Back Side Potential . . . . . . . . . . . . . . . . . . . . . . . . . -VEE, Substrate
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications TJ = 100οC, VDD = 12V, VCC = 5V, VEE = -5V, INVERT Low (Figure 1 Configuration)
Unless Otherwise Specified
PARAMETER
SYMBOL TEST CONDITIONS
MIN
TYP
MAX UNITS
POWER SUPPLIES
V9P Voltage, No External Load
V9P Thermal Shutdown
V9P Thermal Shutdown Recovery
V9P 1µF Tantalum
Capacitor to V9P
-
9
-
V
150
-
-
oC
-
-
125
oC
V9P Current Limiting
65
-
-
mA
VDD Power Supply Current
IDD
-
25
75
mA
VCC Power Supply Current
ICC
-
1.5
25
mA
VEE Power Supply Current
IEE
-75
-23
-
mA
LOGIC/DIGITAL INPUTS (A0-A3, NULLB and SB_H, LASERON1B, LASERON2B with 60kΩ Pullup Resistors; INVERT, RESETB, RLY_IN 60kΩ
with Pulldown Resistors)
Low Level Input Voltage
High Level Input Voltage
Minimum Hysteresis
Low Level Input Current (Inputs with Pullups)
High Level Input Current (Inputs with Pulldowns)
CONSTANT CURRENT CONTROLLER
VIL
VIH
VHYS
IIL
IIH
0
3.5
0.3
-140
-
-
1.5
V
-
VCC + 0.3
V
-
-
V
-
-
µA
-
140
µA
OTA Gate Drive Amp. (A2) Voltage Output Range
VG
-4
-
VCC
V
Current Monitor Amp. (A1) Gain
AVS
9.8
10
10.2
-
Current Monitor Amp. Differential Sense Input Range
VIN
0
-
500
mV
Current Monitor Amp. Input Offset
VIO
-5
-
5
mV
Current Monitor Amp. Common Mode Input Range
VIC
0
-
5
V
SHUNT CURRENT SWITCH CONTROLLER (Note 2) VUPPER = 2V, VLOWER = -1V, Gate Load = 5000pF, VUP1, 2; 1µF Filter Capacitor to
GND, VLOW1, 2; 1µF Filter Capacitor to GND, Unless Otherwise Specified
Shunt Gate Output Rise/Fall time
Propagation Delay, LASERONB1, 2 to SG_1, 2
Drive Output Voltage
tR / tF
tD
VUPPER
VLOWER
10% -90% Rise,
90% -10% Fall
TJ = 100oC
TJ = -25o C
-
-
20
ns
-
80
110
ns
-
60
95
ns
0
-
VCC
V
-4
-
VCC
V
4-5
Share Link: 