HIP4086AP Ver la hoja de datos (PDF) - Intersil
Número de pieza
componentes Descripción
Fabricante
HIP4086AP Datasheet PDF : 9 Pages
| |||
HIP4086
Absolute Maximum Ratings
Supply Voltage, VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 16V
Logic I/O Voltages
Voltage on xHS . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..............
-6V (Transient) to
.8.5-V0.(3-V40tooCVtDoD15+00o.3CV)
Voltage on xHB . . . . . . . . . . . . . . . . . . . . VxHS -0.3V to VxHS +VDD
Voltage on xLO . . . . . . . . . . . . . . . . . . . . . VSS -0.3V to VDD +0.3V
Voltage on xHO . . . . . . . . . . . . . . . . . . . . VxHS -0.3V to VxHB +0.3V
Phase Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V/ns
Thermal Information
Thermal Resistance (Typical, Note 1)
θJA (oC/W)
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70
Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . .150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC
(SOIC - Lead Tips Only)
Operating Conditions
Supply Voltage, VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . +7V to +15V
Voltage on xHB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VxHS + VDD
Voltage on xHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to 80V
Ambient Temperature Range . . . . . . . . . . . . . . . . . . -40oC to 125oC
Junction Temperature Range . . . . . . . . . . . . . . . . . . -40oC to 150oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. θJA is measured with the component mounted on an evaluation PC board in free air.
2. All voltages are relative to VSS unless otherwise specified.
3. x = A, B and C. For example, xHS refers to AHS, BHS and CHS.
Electrical Specifications
PARAMETER
VDD = VxHB = 12V, VSS = VxHS = 0V, RDEL = 20K, RUV = ∞, Gate Capacitance (CGATE) = 1000pF
TJ = 25oC
TJ = -40oC TO
150oC
TEST CONDITIONS
MIN TYP MAX MIN MAX UNITS
SUPPLY CURRENTS AND UNDER VOLTAGE PROTECTION
VDD Quiescent Current
VDD Operating Current
xHB On Quiescent Current
xHI = 5V, xLI = 5V
f = 20kHz, 50% Duty Cycle
xHI = 0V
2.7
3.4
4.2
2.1
4.3
mA
6.3 8.25 10.5
5
11
mA
-
40
80
-
100
µA
xHB Off Quiescent Current
xHB Operating Current
xHI = VDD
f = 20kHz, 50% Duty Cycle
0.6
0.8
1.3
0.5
1.4
mA
0.7
0.9
1.3
-
2.0
mA
Qpump Output Voltage
No Load
11.5 12.5 14 10.5 14.5
V
Qpump Output Current
VxHS = 12V, VxHB = 22V
xHB, xHS Leakage Current
VxHS = 80V, VxHB = 93V
VDD Rising Undervoltage Threshold
RUV open
VDD Falling Undervoltage Threshold
RUV open
Minimum Undervoltage Threshold
RUV = VDD
INPUT PINS: ALI, BLI, CLI, AHI, BHI, CHI, AND DIS
50
100 130
-
140
µA
7
24
45
-
50
µA
6.2
7.1
8.0
6.1
8.1
V
5.75 6.6
7.5
5.6
7.6
V
5
6.2
6.8
4.9
6.9
V
Low Level Input Voltage
-
-
1.0
-
0.8
V
High Level Input Voltage
2.5
-
-
2.7
-
V
Input Voltage Hysteresis
-
35
-
-
-
mV
Low Level Input Current
VIN = 0V
High Level Input Current
VIN = 5V
GATE DRIVER OUTPUT PINS: ALO, BLO, CLO, AHO, BHO, AND CHO
-60 -100 -135 -55 -140
µA
-1
-
+1
-10 +10
µA
Low Level Output Voltage (VOUT - VSS)
Peak Turn-On Current
Peak Turn-Off Current
ISINKING = 30mA
VOUT = 0V
VOUT = 12V
-
100
-
-
200
mV
0.3
0.5
0.7
-
1.0
A
0.7
1.1
1.5
0.5
1.7
A
4
Share Link: 