HIP4084 Ver la hoja de datos (PDF) - Intersil
Número de pieza
componentes Descripción
Fabricante
HIP4084 Datasheet PDF : 6 Pages
| |||
HIP4084
Absolute Maximum Ratings TA = 25oC
Supply Voltage, VDD . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 16V
Logic I/O Voltages . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VDD +0.3V
Voltage on xHS. . . . . . . . .-6V (Transient) to +85V (-40oC to 150oC)
Voltage on xHB. . . . . . . . . . . . . . . . . . . . .VxHS -0.3V to VxHS +VDD
Voltage on xLO . . . . . . . . . . . . . . . . . . . . . . VSS -0.3V to VDD +0.3V
Voltage on xHO . . . . . . . . . . . . . . . . . . . .VxHS -0.3V to VxHB +0.3V
Phase Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V/ns
Thermal Information
Thermal Resistance (Typical, Note 1)
θJA (oC/W)
SOIC Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75oC
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
65oC
Maximum Junction Temperature. . . . . . . . . . . . . . . . . . . . . . . 150oC
Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s). . . . . . . . . . . . . 300oC
(SOIC - Lead Tips Only)
Operating Conditions
Supply Voltage, VDD . . . . . . . . . . . . . . . . . . . . . . . . . +7.0V to +15V
Voltage on VxHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0V to 80V
Voltage on xHB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VxHS + VDD
Operating Ambient Temperature Range . . . . . . . . . . -40oC to 105oC
Operating Junction Temperature Range . . . . . . . . .-40oC to 105oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. θJA is measured with the component mounted on an evaluation PC board in free air.
2. All voltages are relative to VSS unless otherwise specified.
3. x = A, B, C, and D. For example, xHS refers to AHS, BHS, CHS, and DHS.
Electrical Specifications
VDD = VxHB = 12V, VSS = VxHS = 0V, RDEL = 20K, UVLO/EN = ∞, Gate Capacitance (CGATE) = 1000pF
TJ = 25oC
TJ
= -40oC
150oC
TO
PARAMETER
TEST CONDITIONS
MIN
TYP MAX MIN
MAX UNITS
SUPPLY CURRENTS AND UNDER VOLTAGE PROTECTION
VDD Quiescent Current
VDD Operating Current
xHB On Quiescent Current
xHI = 5V, xLI = 5V
f = 20kHz, 50% Duty Cycle
xHI = 0V
3
4
5
8
9.5
12
-
40
80
2
6
mA
7
13
mA
-
100
µA
xHB Off Quiescent Current
xHB Operating Current
xHI = VDD
f = 20kHz, 50% Duty Cycle
0.6
0.8
1.3
0.5
1.4
mA
0.7
0.9
1.3
2.0
mA
QPUMP Output Voltage
No Load
QPUMP Output Current
VxHB = 10V
xHB, xHS Leakage Current
VxHS = 80V, VxHB = 93V
VDD Rising Undervoltage Threshold
RUV Open
VDD Falling Undervoltage Threshold
RUV Open
Minimum Undervoltage Threshold
RUV = VDD
INPUT PINS: ALI, BLI, CLI, DLI, AHI, BHI, CHI, DHI, AND EN
11.5 12.5
14
10.5
14.5
V
-
100
130
-
140
µA
7
24
45
-
50
µA
6.2
7.1
8.0
6.1
8.1
V
5.75
6.6
7.5
5.6
7.6
V
5
6.2
6.8
4.9
6.9
V
Low Level Input Voltage
-
-
1.0
-
0.8
V
High Level Input Voltage
2.5
-
-
2.7
-
V
Input Voltage Hysteresis
-
35
-
-
-
mV
Low Level Input Current
VIN = 0V
60
100
135
55
140
µA
High Level Input Current
VIN = 5V
-1
-
1
-10
10
µA
GATE DRIVER OUTPUT PINS: ALO, BLO, CLO, DLO, AHO, BHO, CHO, AND DHO
Low Level Output Voltage (VOUT-VSS)
Peak Pulse Pullup Current
ISINKING = 30mA
VOUT 0V to 5V
-
100
-
-
200
mV
0.3
0.5
0.7
-
1.0
A
3
Share Link: 