HIP4080A(1995) Ver la hoja de datos (PDF) - Intersil
Número de pieza
componentes Descripción
Fabricante
HIP4080A Datasheet PDF : 15 Pages
| |||
Specifications HIP4080A
Absolute Maximum Ratings
Thermal Information
Supply Voltage, VDD and VCC. . . . . . . . . . . . . . . . . . . . -0.3V to 16V
Logic I/O Voltages . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VDD +0.3V
Voltage on AHS, BHS . . . . -6.0V (Transient) to 80V (25oC to 125oC)
Voltage on AHS, BHS . . . -6.0V (Transient) to 70V (-55oC to 125oC)
Thermal Resistance
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Power Dissipation at +85oC
θJA
+85oC/W
+75oC/W
Voltage on ALS, BLS . . . . . . . -2.0V (Transient) to +2.0V (Transient) SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470mW
Voltage on AHB, BHB . . . . . . . . . VAHS, BHS -0.3V to VAHS, BHS +VDD
Voltage on ALO, BLO . . . . . . . . . . . . . VALS, BLS -0.3V to VCC +0.3V
Voltage on AHO, BHO . . . . . . . VAHS, BHS -0.3V to VAHB, BHB +0.3V
Input Current, HDEL and LDEL . . . . . . . . . . . . . . . . . . -5mA to 0mA
DIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530mW
Storage Temperature Range . . . . . . . . . . . . . . . . . . -65oC to +150oC
Operating Max. Junction Temperature . . . . . . . . . . . . . . . . . +125oC
Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300oC
Phase Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V/ns (For SOIC - Lead Tips Only)
NOTE: All Voltages relative to VSS, unless otherwise specified.
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Operating Conditions
Supply Voltage, VDD and VCC. . . . . . . . . . . . . . . . . . . +9.5V to +15V
Voltage on ALS, BLS . . . . . . . . . . . . . . . . . . . . . . . . . -1.0V to +1.0V
Voltage on AHB, BHB . . . . . . . . . . VAHS, BHS +5V to VAHS, BHS +15V
Input Current, HDEL and LDEL. . . . . . . . . . . . . . . . -500µA to -50µA
Operating Ambient Temperature Range . . . . . . . . . . -40oC to +85oC
Electrical Specifications
PARAMETERS
VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V, RHDEL = RLDEL = 100K, and
TA = +25oC, Unless Otherwise Specified
TJ = +25oC
TJ = - 40oC
TO +125oC
SYMBOL
TEST CONDITIONS
MIN TYP MAX MIN MAX UNITS
SUPPLY CURRENTS AND CHARGE PUMPS
VDD Quiescent Current
IDD
IN- = 2.5V, Other Inputs = 0V
8
11 14
7
14 mA
VDD Operating Current
IDDO Outputs switching f = 500kHz, No Load 9
12 15
8
15 mA
VCC Quiescent Current
ICC
IN- = 2.5V, Other Inputs = 0V,
IALO = IBLO = 0
-
25 80
- 100 µA
VCC Operating Current
ICCO f = 500kHz, No Load
1 1.25 2.0 0.8 3 mA
AHB, BHB Quiescent Current -
Qpump Output Current
IAHB, IBHB IN- = 2.5V, Other Inputs = 0V, IAHO =
-50 -25 -11 -60 -10 µA
IBHO = 0, VDD = VCC =VAHB = VBHB = 10V
AHB, BHB Operating Current
IAHBO,IBHBO f = 500kHz, No Load
0.62 1.2 1.5 0.5 1.9 mA
AHS, BHS, AHB, BHB Leakage Current
IHLK
VBHS = VAHS = 80V,
VAHB = VBHB = 93V
- 0.02 1.0
-
10 µA
AHB-AHS, BHB-BHS Qpump
Output Voltage
VAHB - VAHS IAHB = IAHB = 0, No Load
VBHB - VBHS
11.5 12.6 14.0 10.5 14.5 V
INPUT COMPARATOR PINS: IN+, IN-, OUT
Offset Voltage
VOS Over Common Mode Voltage Range -10 0 +10 -15 +15 mV
Input Bias Current
IIB
0 0.5 2
0
4
µA
Input Offset Current
IOS
-1
0
+1 -2 +2 µA
Input Common Mode Voltage Range CMVR
1
-
VDD
1
VDD
V
-1.5
-1.5
Voltage Gain
AVOL
10 25
-
10
- V/mV
OUT High Level Output Voltage
VOH
IN+ > IN-, IOH = -250µA
VDD
-
-
VDD
-
V
-0.4
- 0.5
OUT Low Level Output Voltage
Low Level Output Current
High Level Output Current
INPUT PINS: DIS
VOL
IN+ < IN-, IOL = +250µA
IOL
VOUT = 6V
IOH
VOUT = 6V
-
- 0.4 - 0.5 V
6.5 14 19 6 20 mA
-17 -10 -3 -20 -2.5 mA
Low Level Input Voltage
High Level Input Voltage
Input Voltage Hysteresis
VIL
Full Operating Conditions
VIH
Full Operating Conditions
-
- 1.0 - 0.8 V
2.5 -
- 2.7 -
V
-
35
-
-
-
mV
Low Level Input Current
High Level Input Current
IIL
VIN = 0V, Full Operating Conditions
-130 -100 -75 -135 -65 µA
IIH
VIN = 5V, Full Operating Conditions
-1
-
+1 -10 +10 µA
3
Share Link: 