HA-2515 Ver la hoja de datos (PDF) - Intersil
Número de pieza
componentes Descripción
Fabricante
HA-2515 Datasheet PDF : 8 Pages
| |||
HA-2515
Absolute Maximum Ratings
Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . 40V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15V
Peak Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA
Operating Conditions
Temperature Range
HA-2515-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 75oC
Thermal Information
Thermal Resistance (Typical, Note 1)
θJA (oC/W) θJC (oC/W)
PDIP Package . . . . . . . . . . . . . . . . . . . 120
N/A
Maximum Junction Temperature (Plastic Package) . . . . . . . 150oC
Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications VSUPPLY = ±15V
PARAMETER
TEMP (oC)
MIN
TYP
INPUT CHARACTERISTICS
Offset Voltage
25
-
5
Full
-
-
Offset Voltage Average Drift
Full
-
30
Bias Current
25
-
125
Full
-
-
Offset Current
25
-
20
Full
-
-
Input Resistance (Note 2)
25
40
100
Common Mode Range
Full
±10.0
-
TRANSFER CHARACTERISTICS
Large Signal Voltage Gain (Notes 3, 6)
25
7.5
15
Full
5
-
Common Mode Rejection Ratio (Note 4)
Full
74
90
Gain Bandwidth Product (Note 5)
25
-
12
OUTPUT CHARACTERISTICS
Output Voltage Swing (Note 3)
Full
±10.0
±12.0
Output Current (Note 6)
25
±10
±20
Full Power Bandwidth (Notes 6, 11)
25
600
1000
TRANSIENT RESPONSE
Rise Time (Notes 3, 7, 8, 9)
25
-
25
Overshoot (Notes 3, 7, 8, 9)
25
-
25
Slew Rate (Notes 3, 7, 9, 12)
25
±40
±60
Settling Time to 0.1% (Notes 3, 7, 9, 12)
25
-
0.25
POWER SUPPLY CHARACTERISTICS
Supply Current
25
-
4
Power Supply Rejection Ratio (Note 10)
Full
74
90
NOTES:
2. This parameter value is based on design calculations.
3. RL = 2kΩ.
4. VCM = ±10V
5. AV >10.
6. VO = ±10V.
7. CL = 50pF.
8. VO = ±200mV.
9. See Transient Response Test Circuits and Waveforms.
10. ∆V = ±5V.
11. Full Power Bandwidth guaranteed based on slew rate measurement using: FPBW = Slew Rate/2πVPEAK.
12. VOUT = ±5V.
MAX
10
14
-
250
500
50
100
-
-
-
-
-
-
-
-
-
50
50
-
-
6
-
UNITS
mV
mV
µV/oC
nA
nA
nA
nA
MΩ
V
kV/V
kV/V
dB
MHz
V
mA
kHz
ns
%
V/µs
µs
mA
dB
2
Share Link: 