HA-2444 Ver la hoja de datos (PDF) - Intersil
Número de pieza
componentes Descripción
Fabricante
HA-2444 Datasheet PDF : 6 Pages
| |||
HA-2444
Electrical Specifications VS = ±15V, RL = 1kΩ, CL ≤ 10pF, VIL = 0.8V, VIH = 2.4V. Unless Otherwise Specified
Specifications Apply to All Channels (Continued)
PARAMETER
TEMP.
HA-2444-5
TEST CONDITIONS
(oC)
MIN
TYP
MAX
UNITS
TRANSIENT RESPONSE
Rise Time (Note 4)
Overshoot (Note 4)
Slew Rate (Note 6)
Settling Time
AV = +1
AV = +1
AV = +1
25
-
7
-
ns
25
-
10
-
%
Full
120
160
-
V/µs
25
-
120
-
ns
SWITCHING CHARACTERISTICS
Channel Select Time
Note 7
0 to 85
-
60
100
ns
-40 to 0
-
80
125
ns
Output Enable Time
Note 8
Full
-
40
100
ns
Digital Input Voltages
D0/D1 Input Current
EN Input Current
Crosstalk Rejection
VIH
VIL
VIL = 0.0V
VIH = 5.0V
VIL = 0.0V
VIH = 5.0V
Note 9
Full
2.4
-
-
V
Full
-
-
0.8
V
Full
-
0.7
1
mA
Full
-
-
1.2
µA
Full
-
-
50
µA
Full
-
-
1.2
µA
25
-
60
-
dB
VIDEO PARAMETERS
Differential Phase
Note 11
25
-
0.03
-
Degrees
Differential Gain
Note 11
25
-
0.03
-
%
Gain Flatness (Note 10)
Chrominance to Luminance Gain
10MHz, AV = +1
Note 11
25
-
0.1
-
dB
25
-
0.1
-
dB
Chrominance to Luminance Delay
Note 11
25
-
7
-
ns
POWER SUPPLY
ICC
IEE
Supply Current (Output Disabled)
Note 14
Full
-
Full
-
Full
-
20
25
mA
20
25
mA
-
10
mA
PSRR
Supply Voltage Range
VS = ±15V to ±20V
Full
65
±8.5
80
-
dB
-
±17.0
V
NOTES:
2. These parameters are not tested. The limits are guaranteed based on lab characterization and reflect lot to lot variation.
3.
4.
Full Power Bandwidth is calculated by:
VOUT = 0 to ±200mV.
FPBW
=
-S----l-e---w-----R----a---t-e--
2πVPEAK
;
VPEAK
=
5V .
5. Settling time to 0.1% with a 10V step. Specified with the channel pre-selected and the output stage enabled. AV = -1.
6. VOUT = -5V to +5V or +5V to -5V.
7. The time required for an enabled HA-2444 to switch from one input channel to another. Measured from the 50% point of the digital input to 50%
of the output. AV = +1 for all channels. VOUT switches from 0V to 5V.
8. The time required to enable the output with a channel preselected. Measured from the 50% point of the Enable input to 4V on the output.
AV = +1 for all channels. VIN = 5V for the selected channel.
9. VIN = 5VP-P, f = 5MHz, for one of the 3 unselected channels. VIN = 0 for the selected channel. AV = +1 for all channels.
10. VIN = 200mVRMS.
11. Tested with a VM700A video tester using a NTC-7 Composite input signal.
12. VOUT = ±10V, VEN = 2.4V, 50% Duty Cycle Max.
13. VOUT = ±5V, VEN = 0.8V.
14. Applies to ICC and IEE. VOUT = 0V, VEN = 0.8V.
3
Share Link: 