HPMX-5001-TY1 Ver la hoja de datos (PDF) - HP => Agilent Technologies

Número de pieza

componentes Descripción

Fabricante

HPMX-5001-TY1

1.5–2.5 GHz Upconverter/Downconverter

HP => Agilent Technologies 

HPMX-5001 Summary Characterization Information

Typical values measured on test board shown in Figure 28 at VCC = 3.0 V, TA = 25°C, RXIF = 110.592 MHz,

TXRF = 1.89 GHz, unless otherwise noted.

Symbol

Parameters and Test Conditions

VIH

CMOS Input High Voltage (Can Be Pulled

up as High as VCC + 7 V)[1]

VIL

CMOS Input Low Voltage

IIH

CMOS Input High Current

IIL

CMOS Input Low Current

ts

DIVMC Setup Time[2,8]

th

DIVMC Hold Time[2,8]

tpd

DIV Propagation Delay[2,8]

Mode Switching Time[3]

Receive Mode

Gc

Receive Conversion Gain[9]

NF

Noise Figure[4]

IIP3

IP1dB

VSWRin

Transmit Mode[6]

Input Third Order Intercept Point

Input 1 dB Gain Compression Point

LO Leakage (2 x fVCO) at IF Port

Input VSWR[5]

PIM3

OP1dB

VSWRout

F3dBIF

Synth Mode

Power Output Level for >35 dB IM3 Suppression[10]

Output 1 dB Gain Compression Point

Output VSWR

LO Suppression (2 x fVCO)

IF 3 dB Bandwidth

Transmitter C/N @ 2 x fVCO + 4 MHz[11]

1LO Frequency Range[7]

Units

V

V

µA

µA

ns

ns

ns

µs

dB

dB

dBm

dBm

dBm

dBm

dBm

dBc

MHz

dBc/Hz

MHz

Typical

≥ VCC - 0.8

≤ VCC - 1.9

< 10

> -300

4

0

<7

<1

1.89 GHz 2.45 GHz

14

13.5

10

10

-8

-9

-18

-18

-57

—

1.3:1

1.3:1

—

0

1.8:1

25

500

+137

-5

0

1.8:1

30

500

+134

750-1200

Notes:

1. All CMOS logic inputs are internally pulled up to logic high level.

2. See Figure 2 for detailed timing diagram.

3. Between any two different biasing modes. This switching time does not include PLL lock-up time.

4. Single sideband noise figure.

5. In modes other than receive, the VSWR may be as high as 10:1.

6. Single-ended 50 Ω RF load, 300 Ω series IF terminations (600 Ω differential), 100 MHz < IF < 300 MHz, 1.89 GHz RF.

7. The LO is followed by a frequency doubler which raises the LO range to 1500-2400 MHz.

8. DIV output AC coupled into a 2 kΩ || 10 pF load. See test diagram, Figure 28.

9. 50 Ω RF source, 110 MHz < IF < 300 MHz, 1.89 GHz or 2.45 GHz RF. There is a 750 Ω resistor on chip between RXIF and RXIFB

(pins 3 and 4). A matching network from 750 Ω to 50␣ Ω is used for this measurement. Insertion loss of the matching network is

included in the net conversion gain figure.

10. PIM3 is the maximum SSB output power for at least 35 dB IM3 spur suppression.

11. Measured at saturated output power for 1.89 GHz. Measured at -5 dBm SSB output power for 2.45␣ GHz.

7-92

Share Link: