7156CS Ver la hoja de datos (PDF) - Intersil

Número de pieza

componentes Descripción

Fabricante

7156CS

High Performance Pin Driver

Intersil 

EL7156

Applications Information

Product Description

The EL7156 is a high performance 40MHz pin driver. It

contains two analog switches connecting VH and VL to OUT.

Depending on the value of the IN pin, one of the two

switches will be closed and the other switch open. An output

enable (OE) is also supplied which opens both switches

simultaneously.

Due to the topology of the EL7156, both the VH and VL pins

can be connected to any voltage between the VS+ and VS-

pins, but VH must be greater than VL in order to prevent

turning on the body diode at the output stage.

The EL7156 is available in both the 8 Ld SOIC and the 8 Ld

PDIP packages. The relevant package should be chosen

depending on the calculated power dissipation.

Three-state Operation

When the OE pin is low, the output is three-state (floating).

The output voltage is the parasitic capacitance’s voltage. It

can be any voltage between VH and VL, depending on the

previous state. At three-state, the output voltage can be

pushed to any voltage between VH and VL. The output

voltage can’t be pushed higher than VH or lower than VL

since the body diode at the output stage will turn on.

Supply Voltage Range and Input Compatibility

The EL7156 is designed for operation on supplies from 5V to

15V (4.5V to 16.5V maximum). “Operating Voltage Range”

on page 6 shows the specifications for the relationship

between the VS+, VS-, VH, VL, and GND pins.

All input pins are compatible with both 3V and 5V CMOS

signals. With a positive supply (VS+) of 5V, the EL7156 is

also compatible with TTL inputs.

Power Supply Bypassing

When using the EL7156, it is very important to use adequate

power supply bypassing. The high switching currents

developed by the EL7156 necessitate the use of a bypass

capacitor between the supplies (VS+ and VS-) and GND

pins. It is recommended that a 2.2µF tantalum capacitor be

used in parallel with a 0.1µF low-inductance ceramic MLC

capacitor. These should be placed as close to the supply

pins as possible. It is also recommended that the VH and VL

pins have some level of bypassing, especially if the EL7156

is driving highly capacitive loads.

Power Dissipation Calculation

When switching at high speeds, or driving heavy loads, the

EL7156 drive capability is limited by the rise in die

temperature brought about by internal power dissipation. For

reliable operation, die temperature must be kept below

TJMAX (+125°C). It is necessary to calculate the power

dissipation for a given application prior to selecting the

package type.

Power dissipation may be calculated:

PD

=

(VS

× IS ) + (CVS

×

VS2

×

f

)

+

[

(

CI

N

T

+

CL

)

×

VO

U

2

T

×

f]

(EQ. 1)

where:

VS is the total power supply to the EL7156 (from VS+ to

GND)

VOUT is the swing on the output (VH to VL)

CVS is the integral capacitance due to VS+

CINT is the integral load capacitance due to VH

IS is the quiescent supply current (3mA max)

f is frequency

TABLE 1. INTEGRAL CAPACITANCE

VS+ = VH(V)

5

10

15

CVS(pF)

80

85

90

CINT(pF)

120

145

180

Having obtained the application’s power dissipation, a

maximum package thermal coefficient may be determined,

to maintain the internal die temperature below TJMAX:

θJA

=

T----J---M-----A----X-----–-----T----M----A----X--

PD

(EQ. 2)

where:

TJMAX is the maximum junction temperature (+125°C)

TMAX is the maximum operating temperature

PD is the power dissipation calculated above

θJA thermal resistance on junction to ambient

θJA is 160°C/W for the SOIC8 package and 100°C/W for the

PDIP8 package when using a standard JEDEC JESD51-3

single-layer test board. If TJMAX is greater than +125°C

when calculated using Equation 2, then one of the following

actions must be taken:

Reduce θJA the system by designing more heat-sinking

into the PCB (as compared to the standard JEDEC

JESD51-3).

Use the PDIP8 instead of the SOIC8 package.

De-rate the application either by reducing the switching

frequency, the capacitive load, or the maximum operating

(ambient) temperature (TMAX).

8

FN7280.3

May 2, 2007

Share Link: