EL5283CY Ver la hoja de datos (PDF) - Intersil
Número de pieza
componentes Descripción
Fabricante
EL5283CY Datasheet PDF : 8 Pages
| |||
EL5283
Absolute Maximum Ratings (TA = 25°C)
Analog Supply Voltage (VS+ to VS-) . . . . . . . . . . . . . . . . . . . +12.6V
Digital Supply Voltage (VSD to GND) . . . . . . . . . . . . . . . . . . . . .+7V
Differential Input Voltage . . . . . . . . . . .[(VS-) -0.2V] to [(VS+) +0.2V]
Common-mode Input Voltage . . . . . . .[(VS-) -0.2V] to [(VS+) +0.2V]
Latch Input Voltage . . . . . . . . . . . . . . . . . . . . -0.2V to [(VSD) +0.2V]
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 125°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
Electrical Specifications VS = ±5V, VSD = 5V, RL = 2.3kΩ, TA = 25°C, unless otherwise specified.
PARAMETER
DESCRIPTION
CONDITION
MIN
TYP
MAX
INPUT
VOS
IB
CIN
VCM
CMRR
OUTPUT
Input Offset Voltage
Input Bias Current
Input Capacitance
Input Voltage Range
Common-mode Rejection Ratio
VCM = 0V, VO = 2.5V
-5.1V < VCM < +2.75V
1
4
-6
-3.5
5
(VS-) - 0.1
(VS+) - 2.25
65
90
VOH
Output High Voltage
VOL
Output Low Voltage
DYNAMIC PERFORMANCE
VIN > 250mV
VIN > 250mV
VSD - 0.6 VSD - 0.4
GND + 0.25 GND + 0.5
tPD+
tPD-
SUPPLY
Positive Going Delay Time
Negative Going Delay Time
VIN = 1VP-P, VOD = 50mV
VIN = 1VP-P, VOD = 50mV
8
12
8
12
IS+
Positive Analog Supply Current
Per comparator
IS-
Negative Analog Supply Current
Per comparator
ISD
Digital Supply Current at No Load Per comparator, output high
Per comparator, output low
7
8.2
5
6.5
4
5
0.75
1
PSRR
Power Supply Rejection Ratio
60
80
LATCH
VLH
VLL
ILH
ILL
tD+
tD-
tS
tH
tPW(D)
Latch Input Voltage High
Latch Input Voltage Low
Latch Input Current High
Latch Input Current Low
Latch Disable to High Delay
VLH = 3.0V
VLL = 0.3V
Latch Disable to Low Delay
Minimum Setup Time
Minimum Hold Time
Minimum Latch Disable Pulse Width
2.0
0.8
-50
-30
-50
-40
6
6
2
1
10
UNIT
mV
µA
pF
V
dB
V
V
ns
ns
mA
mA
mA
mA
dB
V
V
µA
µA
ns
ns
ns
ns
ns
2
Share Link: 