EL2008 Ver la hoja de datos (PDF) - Intersil
Número de pieza
componentes Descripción
Fabricante
EL2008 Datasheet PDF : 8 Pages
| |||
EL2008
Absolute Maximum Ratings (TA = 25°C)
VS Supply Voltage (V+ - V-) . . . . . . . . . . . . . . . . . . . . ±18V or 36V
VIN Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±15V or VS
If the input exceeds the ratings shown (or the supplies) or if the input to output
voltage exceeds ±7.5V then the input current must be limited to ±50mA. See
the applications section for more information.
IIN Input Current (See above note) . . . . . . . . . . . . . . . . . . . ±50mA
PD Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
The maximum power dissipation depends on package type, ambient
temperature and heat sinking. See the characteristic curves for more details.
TA Operating Temperature Range . . . . . . . . . . . . . . 0°C to +75°C
TJ Operating Junction Temp . . . . . . . . . . . . . . . . . . . . . . . . . 175°C
TST Storage Temp Range . . . . . . . . . . . . . . . . . . .-65°C to +150°C
TLD Lead Solder Temp <10 seconds . . . . . . . . . . . . . . . . . . . 300°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
Electrical Specifications VS= ±15V, RS= 50Ω, unless otherwise specified.
TEST CONDITIONS
PARAMETER
VOS
DESCRIPTION
Output Offset Voltage
IIN
Input Current
RIN
Input Impedance
AV1
Voltage Gain
AV2
Voltage Gain
AV3
Voltage Gain, VS = ±15V
V01
Output Voltage Swing
V02
Output Voltage Swing
R01
Output Impedance
R02
Output Impedance
IO
Output Current
IS
PSRR
Supply Current
Supply Rejection (Note 2)
VIN
LOAD
0
∞
0
∞
±12V
±10V
±10V
±3V
±14V
±12V
±10V
±10V
±12V
100Ω
∞
10Ω
10Ω
100Ω
10Ω
±10mA
±1A
(Note 1)
0
∞
0
∞
TEMP
25°C
TMIN, TMAX
25°C
TMIN, TMAX
25°C
25°C
25°C
25°C
25°C
25°C
25°C
25°C
25°C
TMIN, TMAX
25°C
25°C
VS+, VS-
SR1
Supply Sensitivity (Note 3)
∞
Slew Rate (Note 4)
±10V
50Ω
±10V
10Ω
25°C
25°C
25°C
SR2
tR, tF
BW
Slew Rate (Note 5)
Rise/Fall Time
-3dB Bandwidth
±5V
10Ω
100mV
10Ω
100mV
10Ω
25°C
25°C
25°C
CIN
THD
Input Capacitance
25°C
25°C
MIN
-40
-50
-35
-50
0.5
0.985
0.88
0.87
±13
±10.5
1.25
1
12
60
LIMITS
TYP
10
-5
2
0.9995
0.91
0.89
±11
1.8
0.8
1.8
17
2500
1500
800
7
55
25
MAX
+40
+50
+35
+50
2.5
1.15
26
2
1
UNITS
mV
mV
µA
µA
MΩ
V/V
V/V
V/V
V
V
Ω
Ω
A
A
mA
dB
mV/V
V/µs
V/µs
V/µs
ns
MHz
pF
%
NOTES:
1. Force the input to +12V and the output to +10V and measure the output current. Repeat with -12V and -10V on the output.
2. VS = ±4.5V then VS is changed to ±18V.
3. VS+ = +15V, VS- = -4.5V then VS - is changed to -18V and VS- = -15V, VS+ = +4.5V then VS+ is changed to +18V.
4. Slew Rate is measured between VOUT = +5V and -5V.
5. 7:Slew Rate is measured between VOUT = +2.5V and -2.5V.
2
Share Link: 