CY14B104K Ver la hoja de datos (PDF) - Cypress Semiconductor
Número de pieza
componentes Descripción
Fabricante
CY14B104K Datasheet PDF : 29 Pages
| |||
PRELIMINARY
CY14B104K/CY14B104M
Pin Definitions (continued)
Pin Name IO Type
Description
INT
VSS
VCC
HSB
VCAP
Output
Interrupt Output. Programmable to respond to the clock alarm, the watchdog timer, and the power
monitor. Also programmable to either active HIGH (push or pull) or LOW (open drain).
Ground Ground for the Device. Must be connected to ground of the system.
Power Supply Power Supply Inputs to the Device. 3.0V +20%, –10%
Input/Output Hardware Store Busy: When LOW this output indicates that a hardware store is in progress. When
pulled LOW external to the chip it initiates a nonvolatile STORE operation. A weak internal pull up resistor
keeps this pin HIGH if not connected. (connection optional)
Power Supply AutoStore Capacitor. Supplies power to the nvSRAM during power loss to store data from SRAM to
nonvolatile elements.
Device Operation
AutoStore Operation
The CY14B104K/CY14B104M nvSRAM is made up of two
functional components paired in the same physical cell. These
are a SRAM memory cell and a nonvolatile QuantumTrap cell.
The SRAM memory cell operates as a standard fast static RAM.
Data in the SRAM is transferred to the nonvolatile cell (the
STORE operation), or from the nonvolatile cell to the SRAM (the
RECALL operation). Using this unique architecture, all cells are
stored and recalled in parallel. During the STORE and RECALL
operations SRAM read and write operations are inhibited. The
CY14B104K/CY14B104M supports infinite reads and writes
similar to a typical SRAM. In addition, it provides infinite RECALL
operations from the nonvolatile cells and up to 200K STORE
operations.
SRAM Read
The CY14B104K/CY14B104M performs a read cycle whenever
CE and OE are LOW, and WE and HSB are HIGH. The address
specified on pins A0-18 or A0-17 determines which of the 524,288
data bytes or 262,144 words of 16 bits each are accessed. When
the read is initiated by an address transition, the outputs are valid
after a delay of tAA (read cycle #1). If the read is initiated by CE
or OE, the outputs are valid at tACE or at tDOE, whichever is later
(read cycle #2). The data output repeatedly responds to address
changes within the tAA access time without the need for transi-
tions on any control input pins. This remains valid until another
address change or until CE or OE is brought HIGH, or WE or
HSB is brought LOW.
SRAM Write
A write cycle is performed when CE and WE are LOW and HSB
is HIGH. The address inputs must be stable before entering the
write cycle and must remain stable until CE or WE goes HIGH at
the end of the cycle. The data on the common IO pins IO0-7 are
written into the memory if it is valid tSD before the end of a WE
controlled write or before the end of an CE controlled write. It is
recommended that OE be kept HIGH during the entire write cycle
to avoid data bus contention on common IO lines. If OE is left
LOW, internal circuitry turns off the output buffers tHZWE after WE
goes LOW.
The CY14B104K/CY14B104M stores data to the nvSRAM using
one of three storage operations. These three operations are:
hardware store, activated by the HSB; software store, activated
by an address sequence; AutoStore, on device power down. The
AutoStore operation is a unique feature of QuantumTrap
technology and is enabled by default on the
CY14B104K/CY14B104M.
During normal operation, the device draws current from VCC to
charge a capacitor connected to the VCAP pin. This stored
charge is used by the chip to perform a single STORE operation.
If the voltage on the VCC pin drops below VSWITCH, the part
automatically disconnects the VCAP pin from VCC. A STORE
operation is initiated with power provided by the VCAP capacitor.
Figure 2. AutoStore Mode
Vcc
0.1uF
Vcc
WE
VCAP
VSS
VCAP
Figure 2 shows the proper connection of the storage capacitor
(VCAP) for automatic store operation. Refer to DC Electrical
Characteristics on page 14 for the size of the VCAP.
To reduce unnecessary nonvolatile stores, AutoStore and
hardware store operations are ignored unless at least one write
operation has taken place since the most recent STORE or
RECALL cycle. Software initiated STORE cycles are performed
regardless of whether a write operation has taken place.
Document #: 001-07103 Rev. *I
Page 3 of 29
[+] Feedback
Share Link: 