ATF-35143-BLK Ver la hoja de datos (PDF) - HP => Agilent Technologies
Número de pieza
componentes Descripción
Fabricante
ATF-35143-BLK
HP => Agilent Technologies
ATF-35143-BLK Datasheet PDF : 19 Pages
| |||
ATF-35143 Typical Scattering Parameters, VDS = 2 V, IDS = 10 mA
Freq.
S11
S21
S12
GHz Mag. Ang. dB Mag. Ang. dB Mag. Ang.
0.50
0.75
1.00
1.50
1.75
2.00
2.50
3.00
4.00
5.00
6.00
7.00
8.00
9.00
10.00
11.00
12.00
13.00
14.00
15.00
16.00
17.00
18.00
0.99 -18.75 15.89
0.97 -29.11 15.79
0.95 -38.28 15.61
0.91 -55.52 15.17
0.89 -63.78 14.92
0.86 -71.82 14.65
0.81 -87.59 14.11
0.76 -103.22 13.54
0.66 -134.81 12.40
0.61 -165.34 11.29
0.58 165.88 10.27
0.57 137.00 9.27
0.58 110.78 8.33
0.61 86.75 7.32
0.65 66.25 6.44
0.69 46.88 5.54
0.72 27.76 4.56
0.74
8.62 3.45
0.77 -5.28 2.33
0.82 -16.03 1.29
0.82 -28.32 0.19
0.84 -40.43 -0.87
0.86 -56.14 -1.99
6.23 164.76 -32.40 0.024 77.63
6.16 155.98 -28.87 0.036 70.58
6.03 148.42 -26.56 0.047 64.88
5.73 133.92 -23.61 0.066 54.16
5.57 127.01 -22.62 0.074 49.11
5.40 120.27 -21.72 0.082 44.08
5.08 107.36 -20.35 0.096 34.60
4.76 95.04 -19.41 0.107 25.71
4.17 71.95 -18.27 0.122 9.04
3.67 50.43 -17.65 0.131 -5.97
3.26 30.28 -17.33 0.136 -20.15
2.91 10.68 -17.14 0.139 -33.84
2.61 -8.09 -17.14 0.139 -45.60
2.32 -26.38 -17.20 0.138 -57.65
2.10 -43.90 -17.20 0.138 -68.22
1.89 -61.97 -17.27 0.137 -79.30
1.69 -79.90 -17.39 0.135 -90.87
1.49 -97.18 -17.79 0.129 -102.19
1.31 -112.92 -18.20 0.123 -110.80
1.16 -128.66 -18.56 0.118 -120.09
1.02 -144.87 -18.79 0.115 -129.92
0.91 -159.49 -18.79 0.115 -139.60
0.80 -175.19 -19.33 0.108 -149.17
S22
MSG/MAG
Mag. Ang.
dB
0.63 -14.09
0.61 -19.69
0.60 -26.10
0.57 -38.73
0.56 -44.79
0.54 -50.70
0.51 -61.95
0.47 -72.47
0.41 -91.47
0.34 -110.05
0.27 -129.24
0.21 -150.49
0.17 -174.77
0.13 154.01
0.11 118.18
0.14 78.36
0.19 49.57
0.26 29.95
0.33
9.45
0.39 -7.98
0.45 -22.30
0.51 -32.23
0.57 -44.43
24.14
22.30
21.08
19.39
18.75
18.19
17.23
16.48
15.34
14.47
13.80
13.21
12.73
10.69
9.85
9.16
8.34
7.35
6.51
6.51
5.48
5.24
4.72
ATF-35143 Typical Noise Parameters
VDS = 2 V, IDS = 10 mA
Freq.
Fmin
Γopt
Rn/50
Ga
GHz
dB
Mag.
Ang.
-
dB
0.5
0.10
0.88
5.0
0.15
20.5
0.9
0.11
0.84
14.0
0.15
19.0
1.0
0.12
0.83
16.0
0.15
18.6
1.5
0.17
0.77
26.0
0.15
17.5
1.8
0.20
0.74
31.9
0.15
16.9
2.0
0.23
0.71
37.3
0.14
16.4
2.5
0.29
0.66
48.6
0.14
15.7
3.0
0.34
0.60
60.6
0.12
15.0
4.0
0.46
0.52
86.8
0.12
13.6
5.0
0.58
0.45
115.3
0.08 12.4
6.0
0.69
0.40
145.8
0.05 11.3
7.0
0.81
0.37
177.7
0.05 10.3
8.0
0.92
0.35 -149.3
0.07
9.5
9.0
1.04
0.35 -115.6
0.12
8.8
10.0
1.16
0.37
-81.8
0.22
8.3
30
25
20
MSG
15
10
S21
MAG
5
0
-5
0
5
10
15
20
FREQUENCY (GHz)
Figure 19. MSG/MAG and |S21|2 vs.
Frequency at 2 V, 10 mA.
Notes:
1. Fmin values at 2 GHz and higher are based on measurements while the Fmins below 2 GHz have been extrapolated. The Fmin values are
based on a set of 16 noise figure measurements made at sixteen different impedances using an ATN NP5 test system. From these
measurements a true Fmin is calculated. Refer to the noise parameter application section for more information.
2. S and noise parameters are measured on a microstrip line made on 0.025 inch thick alumina carrier. The input reference plane is at the
end of the gate lead. The output reference plane is at the end of the drain lead. The parameters include the effect of four plated
through via holes connecting source landing pads on top of the test carrier to the microstrip ground plane on the bottom side of the
carrier. Two 0.020 inch diameter via holes are placed within 0.010 inch from each source lead contact point, one via on each side of
that point.
7
Share Link: