AT49BV002A Ver la hoja de datos (PDF) - Atmel Corporation
Número de pieza
componentes Descripción
Fabricante
AT49BV002A Datasheet PDF : 19 Pages
| |||
AT49BV002A(N)(T)
5. Command Definition Table
Command Sequence
Bus
Cycles
1st Bus
Cycle
Addr Data
2nd Bus
Cycle
Addr Data
3rd Bus
Cycle
Addr Data
4th Bus
Cycle
Addr Data
5th Bus
Cycle
Addr Data
6th Bus
Cycle
Addr Data
Read
Chip Erase
1
Addr
DOUT
6
555
AA
AAA(2)
55
555
80
555
AA
AAA
55
555
10
Sector Erase
6
555
AA
AAA
55
555
80
555
AA
AAA
55
SA(5)
30
Byte Program
Boot Block Lockout(3)
4
555
AA
AAA
55
555
A0
Addr
DIN
6
555
AA
AAA
55
555
80
555
AA
AAA
55
555
40
Product ID Entry
3
555
AA
AAA
55
555
90
Product ID Exit(4)
3
555
AA
AAA
55
555
F0
Product ID Exit(4)
1
XXXX F0
Notes:
1. The DATA FORMAT in each bus cycle is as follows: I/O7 - I/O0 (Hex). The address format in each bus cycle is as follows:
A11 - A0 (Hex); A11 - A17 (don’t care).
2. Since A11 is don’t care, AAA can be replaced with 2AA.
3. The 16K byte boot sector has the address range 00000H to 03FFFH for the AT49BV002A(N) and 3C000H to 3FFFFH for the
AT49BV002A(N)T
4. Either one of the Product ID Exit commands can be used.
5. SA = sector addresses:
For the AT49BV002A(N):
SA = 00000 to 03FFF for BOOT BLOCK
SA = 04000 to 05FFF for PARAMETER BLOCK 1
SA = 06000 to 07FFF for PARAMETER BLOCK 2
SA = 08000 to FFFF for MAIN MEMORY ARRAY BLOCK 1
SA = 10000 to 1FFFF for MAIN MEMORY ARRAY BLOCK 2
SA = 20000 to 2FFFF for MAIN MEMORY ARRAY BLOCK 3
SA = 30000 to 3FFFF for MAIN MEMORY ARRAY BLOCK 4
For the AT49BV002A(N)T:
SA = 3C000 to 3FFFF for BOOT BLOCK
SA = 3A000 to 3BFFF for PARAMETER BLOCK 1
SA = 38000 to 39FFF for PARAMETER BLOCK 2
SA = 30000 to 37FFF for MAIN MEMORY ARRAY BLOCK 1
SA = 20000 to 2FFFF for MAIN MEMORY ARRAY BLOCK 2
SA = 10000 to 1FFFF for MAIN MEMORY ARRAY BLOCK 3
SA = 00000 to 0FFFF for MAIN MEMORY ARRAY BLOCK 4
6. Absolute Maximum Ratings*
Temperature Under Bias ............................... -55°C to +125°C
Storage Temperature..................................... -65°C to +150°C
All Input Voltages
(including NC Pins)
with Respect to Ground ...................................-0.6V to +6.25V
All Output Voltages
with Respect to Ground .............................-0.6V to VCC + 0.6V
Voltage on OE
with Respect to Ground ...................................-0.6V to +13.5V
*NOTICE:
Stresses beyond those listed under “Absolute Maxi-
mum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional
operation of the device at these or any other condi-
tions beyond those indicated in the operational sec-
tions of this specification is not implied. Exposure to
absolute maximum rating conditions for extended
periods may affect device reliability.
7
3353G–FLASH–8/05
Share Link: 